4、主机飞车保护试验 Protection test of M/E flywheel trip 45、淡水高温停车试验Shut- down test of f/w. high temp 46、滑油低压停车试验Shut- down test of l o. low press. 47、高压油泵齿条格数 Tooth sector of high pressure oil pump 48、喷油提前角太大(小) The advance angle is too large(smal) 49、喷油嘴雾化不良 The atomization of nozzle is too poor. 50、喷油嘴压力太高(低) The pressure of nozzle is too high(low). 51、喷油嘴漏油 The nozzle leakage. 52、盘车装置离合保护试验 The protection test of turning gear clutch 53、调速器有故障 The governor has failed 液压链条压紧装置 Hydraulic chain tightener 55、缸头启动阀 The cylinder cover starting valve 56、缸头启动阀发烫 The cylinder cover starting valve is too hot 57、缸头启动阀漏气 The cylinder cover starting valve leakage 58、气缸油单向阀漏 The cylinder oil one- way valve leakage 59、气缸油单向阀装反 The cylinder oil one-way valve is fitted reversely 60、气缸油进油过多(少) The inlet cylinder oil is too much( (little) 61、拉缸 Cylinder score 62、咬缸 Cylinder seizing 63、敲缸 64、燃烧不良 Poor combustion 65、排气中有水份 The exhaust gas is with water vapour 66、排气冒黑烟(呈淡蓝色) The exhaust gas is black( light blue) 67、排气管振动(漏烟) Exhaust pipe vibration( eakage) 68、排气管增加支架 Attached bracket of exhaust pipe 69、排气管支架螺丝未扳紧 he bracket of exhaust pipe. 70、泠却水管漏水 The cooling water pipe leakage 71、滑油管漏油L. O pipe leakage 72、油底壳(循环滑油舱/主机内部)不干净 The Oil pan(The circulating L.O. tank/ The inside of M/E )is not clean 73、主机出油点不畅 The m/e oil outlets are blocked 74、主机内部螺丝保险未装好 The safety of inner screw of M/E is not fitted properly 75、主机贯穿螺丝泵紧提交ME. through bolt submission 76、主机底脚紧固螺丝提交 M. E bottom fastening bolt submission. 77、滑油(燃油)自清滤器不动作TheL.O.(FO.) filter doesn' t work. Ⅱ发电机提交过程用语:( for diesel engine generator) 1、主发电机内部清洗提交 The cleanness inside the main generator to be confirmed. 2、主发电机曲拐挡提交 The main generator crankshaft deflection to be confirmed 3、主发电机安装提交 The installation of main generator to be confirmed. 4、飞车保护提交 The protection of flywheel trip to be confir 5、滑油低压停车提交 The auto- stop function of L C. low pressure to be confirmed 6、淡水高温停车提交 The auto-shop function of F w. high temperature to be confirmed 7、主发电机负载试验 The load test of main generator 8、100%负载试验100% load test of generator 9、调速器突加/突卸试验 Instant load/ unload test of governor
6 44、主机飞车保护试验 Protection test of M/E flywheel trip. 45、淡水高温停车试验 Shut-down test of F/W. high temp. 46、滑油低压停车试验 Shut-down test of L.O. low press. 47、高压油泵齿条格数 Tooth sector of high pressure oil pump. 48、喷油提前角太大（小） The advance angle is too large (small). 49、喷油嘴雾化不良 The atomization of nozzle is too poor. 50、喷油嘴压力太高（低） The pressure of nozzle is too high (low). 51、喷油嘴漏油 The nozzle leakage. 52、盘车装置离合保护试验 The protection test of turning gear clutch. 53、调速器有故障 The governor has failed. 54、液压链条压紧装置 Hydraulic chain tightener. 55、缸头启动阀 The cylinder cover starting valve. 56、缸头启动阀发烫 The cylinder cover starting valve is too hot. 57、缸头启动阀漏气 The cylinder cover starting valve leakage. 58、气缸油单向阀漏 The cylinder oil one-way valve leakage. 59、气缸油单向阀装反 The cylinder oil one-way valve is fitted reversely. 60、气缸油进油过多(少) The inlet cylinder oil is too much (little). 61、拉缸 Cylinder score 62、咬缸 Cylinder seizing 63、敲缸 Cylinder knocking 64、燃烧不良 Poor combustion 65、排气中有水份 The exhaust gas is with water vapour. 66、排气冒黑烟（呈淡蓝色） The exhaust gas is black（light blue）. 67、排气管振动（漏烟） Exhaust pipe vibration (leakage). 68、排气管增加支架 Attached bracket of exhaust pipe. 69、排气管支架螺丝未扳紧 The bracket of exhaust pipe. 70、冷却水管漏水 The cooling water pipe leakage. 71、滑油管漏油 L.O pipe leakage. 72、油底壳(循环滑油舱 / 主机内部)不干净 The Oil pan（The circulating L.O. tank / The inside of M/E ）is not clean. 73、主机出油点不畅 The M/E oil outlets are blocked. 74、主机内部螺丝保险未装好 The safety of inner screw of M/E is not fitted properly. 75、主机贯穿螺丝泵紧提交 M.E. through bolt submission. 76、主机底脚紧固螺丝提交 M.E bottom fastening bolt submission. 77、滑油（燃油）自清滤器不动作 The L.O. (F.O.) filter doesn’t work. Ⅱ发电机提交过程用语：（for diesel engine generator） 1、主发电机内部清洗提交 The cleanness inside the main generator to be confirmed. 2、主发电机曲拐挡提交 The main generator crankshaft deflection to be confirmed. 3、主发电机安装提交 The installation of main generator to be confirmed. 4、飞车保护提交 The protection of flywheel trip to be confirmed. 5、滑油低压停车提交 The auto-stop function of L.O. low pressure to be confirmed. 6、淡水高温停车提交 The auto-shop function of F.W. high temperature to be confirmed. 7、主发电机负载试验 The load test of main generator. 8、100％负载试验 100％ load test of generator. 9、调速器突加/突卸试验 Instant load/ unload test of governor
10、100%到50%突卸试验100%to50% instant unload test 11、50%到零突卸试验 0% to nil instant unload test 12、零到100%突加试验Nilt50% instant load test 13、主发电机并电试验 The parallel test of generators 14、测量热拐挡(外压) The measurement of thermal deflection( exterior pressure) 15、应急发电机负荷试验 The load test of emergency generator 16、应急发电机飞车保护试验 The protection test of flywheel trip of emergency generator 17、应急发电机淡水高温停车试验 The auto- stop test of emergency generator F w.high-temp 18、应急发电机滑油低压停车试验 The auto- stop test of emergency generator L.O.low-pres 19、应急发电机调速突加突卸试验 The instant load& unload test of emergency generator governor 20、应急发电机合主发电机联锁试验 The parallel of emergency and main generators Ⅲ空压机合空气系统提交用语( for air compressor and air system) 1、空压机垫片提交 The air compressor washer to be confirmed. 2、空压机找中提交 The alignment of air compressor to be confirmed. 3、淡水高温报警试验 Alarm test off w. high temperature 4、滑油低压报警试验 Alarm test of l o. low pressure 5、安全阀提交 The safety valve to be submitted 6、空压机冲气试验 The filling test of air compressor 7、空压机高压(低压)自动停车试验High- pressure(Low- pressure, auto-stop test of air compressor 8、主空气瓶密性提交 Gas tightness submission of main air reservoi 10、控制空气减压阀试验 Test of control air pressure-reducing valve( mitted 9、主空气瓶安全阀提交 The main air reservoir safety valve to be submitted ll、控制空气瓶密性试验 Gas tightness test of control air reservoir 12、控制空气瓶安全阀试验 The safety valve test of control air bottle 13、干燥器效用试验 The effect test of dehumidifier 14、日用空气减压阀试验 The test of service air pressure-reducing valve 15、日用空气瓶密性试验 The gas tightness test of service air reservoir 16、日用空气安全阀提交 The safety valve of service air reservoir to be confirmed 17、副空气瓶密性试验 The gas tightness test of aux. air reservoir 18、副空气瓶安全阀提交 The aux. air bottle safety valve to be submitted 19、应急空压机安全阀试验 The safety valve test of emergency air compressor 20、应急空压机冲气试验 The filling test of emergency air compressor Ⅳ.锅炉提交用语:( for boiler) 1、主锅炉密性试验 The tightness test of main boiler 2、制炉 Boiler pickling(浸酸,酸洗) 3、炉内清洁提交 The inside cleanness to be checked. 锅炉给水泵运转提交 The running test of boiler water- feed pump 5、给水泵真空(自动转换)试验 The vacuum test( the auto- -shifting test) of water- feed pump 6、自动给水提交 The auto water-feed system to be confirmed 7、锅炉燃油泵安全阀提交 The safety valve of boiler F:O. pump to be submitted. 8、锅炉燃油真空试验 The vacuum test of boiler F.O.pump 9、锅炉燃油泵自动转换试验 The auto- shifting test of boiler Fc.pump 10、锅炉安全阀提交 The boiler safety valve to be confirmed ll、锅炉蒸发量试验 The test of boiler evaporation
7 10、100％到 50％突卸试验 100％ to 50% instant unload test. 11、50％到零突卸试验 50％ to nil instant unload test. 12、零到 100％突加试验 Nil to 50% instant load test. 13、主发电机并电试验 The parallel test of generators. 14、测量热拐挡（外压） The measurement of thermal deflection (exterior pressure). 15、应急发电机负荷试验 The load test of emergency generator. 16、应急发电机飞车保护试验 The protection test of flywheel trip of emergency generator. 17、应急发电机淡水高温停车试验 The auto-stop test of emergency generator F.W. high-temp. 18、应急发电机滑油低压停车试验 The auto-stop test of emergency generator L.O. low-press. 19、应急发电机调速突加突卸试验 The instant load & unload test of emergency generator governor. 20、应急发电机合主发电机联锁试验 The parallel of emergency and main generators. Ⅲ空压机合空气系统提交用语（for air compressor and air system） 1、空压机垫片提交 The air compressor washer to be confirmed. 2、空压机找中提交 The alignment of air compressor to be confirmed. 3、淡水高温报警试验 Alarm test of F.W. high temperature. 4、滑油低压报警试验 Alarm test of L.O. low pressure. 5、安全阀提交 The safety valve to be submitted. 6、空压机冲气试验 The filling test of air compressor. 7、空压机高压(低压)自动停车试验 High-pressure (Low- pressure) auto-stop test of air compressor. 8、主空气瓶密性提交 Gas tightness submission of main air reservoir. 9、主空气瓶安全阀提交 The main air reservoir safety valve to be submitted 10、控制空气减压阀试验 Test of control air pressure-reducing valve. 11、控制空气瓶密性试验 Gas tightness test of control air reservoir. 12、控制空气瓶安全阀试验 The safety valve test of control air bottle. 13、干燥器效用试验 The effect test of dehumidifier. 14、日用空气减压阀试验 The test of service air pressure-reducing valve. 15、日用空气瓶密性试验 The gas tightness test of service air reservoir. 16、日用空气安全阀提交 The safety valve of service air reservoir to be confirmed. 17、副空气瓶密性试验 The gas tightness test of aux. air reservoir. 18、副空气瓶安全阀提交 The aux. air bottle safety valve to be submitted. 19、应急空压机安全阀试验 The safety valve test of emergency air compressor. 20、应急空压机冲气试验 The filling test of emergency air compressor. Ⅳ. 锅炉提交用语：（for boiler） 1、主锅炉密性试验 The tightness test of main boiler. 2、制炉 Boiler pickling(浸酸，酸洗). 3、炉内清洁提交 The inside cleanness to be checked. 4、锅炉给水泵运转提交 The running test of boiler water-feed pump. 5、给水泵真空（自动转换）试验 The vacuum test（the auto-shifting test）of water-feed pump. 6、自动给水提交 The auto water-feed system to be confirmed. 7、锅炉燃油泵安全阀提交 The safety valve of boiler F.O. pump to be submitted. 8、锅炉燃油真空试验 The vacuum test of boiler F.O. pump. 9、锅炉燃油泵自动转换试验 The auto-shifting test of boiler F.O. pump. 10、锅炉安全阀提交 The boiler safety valve to be confirmed. 11、锅炉蒸发量试验 The test of boiler evaporation
12、锅炉自动化试验 The automation test of boiler V轴舵系提交过程用语( for shafting and steering gear system) 1、请检验照光靶 Please check the lighting target 2、请检验轴系照光(舵系)对中 Please check the alignment of shafting( steering gear system) 3、请检验轴孔加工圆 Please check the shaft hole 4、请检验搪孔尺寸(光洁度) Please check the boring size( cleanness)) 5、艉轴管衬套压紧验收。 The stern tube liner tightenness to be approved 6、车叶压紧验收。 The propeller impeller tightenness to be approved 7、请检验舵叶零位 Please check the rudder nil position 8、左(右)37°Port( Starboard)3 Ⅵ投油提交过程用语 Delivery expression for flushing 1、投油提交 The flushing submission 2、油温太低 The oil temperature is too low. 3、安装震动器 Vibrator installation 4、油不干净。 The oil is not clean 5、油有砂粒 The oil is with particles 6、油有铁末 The oil is with slag 7、再投一小时 One more hour flushing 8、请做得好一些 Please make it better Ⅶ水下件提交过程用语( for underwater equipment) 1、舷旁阀密性提交 The tightness test of hull valve 2、应急消防泵进水阀密性试验 The tightness test of inlet valve for emergency fire pump 3、清洗阀(透气阀)密性验收 The tightness test of flushing valve (vent valve 4、艏(舯)吃水阀密性试验 The tightness test of fore(mid-ship) draft valve. 5、测深仪(记程仪)密性试验 The tightness test of sounder(log) 6、焊缝不好,请补焊。 The seam is not good. Please reweld it. 7、焊缝不平整,请磨光 The seam is not smooth. Please grind it 8、漏气 Air leakage 9、请打开阀 Please open the valve Ⅷ.锚绞机提交过程用语( for anchor windlass) 1、请检验锚机垫片 Please check the windlass washer 2、请检验轴系对中 Please check the alignment of shafting 3、请检验锚机旁撑 Please check the windlass attached bracket 4、液压泵压力偏高(低) The pressure of hydraulic pump is too high(ow) 5、油马达压力偏高(低) The oil motor pressure is too high(ow 6、液压油温度高 7、冷却水温度高 The cooling water temperature is high 8、锚机液压泵清洁 To clean the anchor windlass( hydraulic pump 9、请检验油柜 Please inspect the oil tanks 10、试验时间已到。 The testing time is up 有故 2、不动作 It doesn't work
8 12、锅炉自动化试验 The automation test of boiler. Ⅴ.轴舵系提交过程用语（for shafting and steering gear system） 1、请检验照光靶 Please check the lighting target. 2、请检验轴系照光(舵系)对中 Please check the alignment of shafting（steering gear system）. 3、请检验轴孔加工圆 Please check the shaft hole. 4、请检验搪孔尺寸（光洁度） Please check the boring size（cleanness）. 5、艉轴管衬套压紧验收。 The stern tube liner tightenness to be approved. 6、车叶压紧验收。 The propeller impeller tightenness to be approved. 7、请检验舵叶零位 Please check the rudder nil position. 8、左（右）37° Port (Starboard) 37° Ⅵ.投油提交过程用语 Delivery expression for flushing 1、投油提交 The flushing submission. 2、油温太低 The oil temperature is too low. 3、安装震动器 Vibrator installation. 4、油不干净。 The oil is not clean. 5、油有砂粒 The oil is with particles. 6、油有铁末 The oil is with slag. 7、再投一小时 One more hour flushing. 8、请做得好一些 Please make it better. Ⅶ.水下件提交过程用语（for underwater equipment） 1、舷旁阀密性提交 The tightness test of hull valve. 2、应急消防泵进水阀密性试验 The tightness test of inlet valve for emergency fire pump. 3、清洗阀（透气阀）密性验收 The tightness test of flushing valve（vent valve）. 4、艏(舯)吃水阀密性试验 The tightness test of fore（mid-ship）draft valve. 5、测深仪（记程仪）密性试验 The tightness test of sounder（log）. 6、焊缝不好，请补焊。 The seam is not good. Please reweld it. 7、焊缝不平整，请磨光 The seam is not smooth. Please grind it. 8、漏气 Air leakage 9、请打开阀 Please open the valve. Ⅷ.锚绞机提交过程用语（ for anchor windlass） 1、请检验锚机垫片 Please check the windlass washer. 2、请检验轴系对中 Please check the alignment of shafting. 3、请检验锚机旁撑 Please check the windlass attached bracket. 4、液压泵压力偏高（低） The pressure of hydraulic pump is too high (low). 5、油马达压力偏高（低） The oil motor pressure is too high (low). 6、液压油温度高 The hydraulic oil temperature is high. 7、冷却水温度高 The cooling water temperature is high. 8、锚机液压泵清洁 To clean the anchor windlass（hydraulic pump）. 9、请检验油柜 Please inspect the oil tanks. 10、试验时间已到。The testing time is up. 11、有故障 There’s a failure (It’s abnormal). 12、不动作 It doesn’t work
13、振动厉害 The vibration is violent 14、噪音太大 The decibel(分贝) is too high( The noise is too loud 15、间隙太大(小) Too much/too little clearance 16、负荷太重 Overload 17、速度太快 oo fast 18、把液压泵盖打开 Please open the hydraulic pump cover 19、把冷却器拆下 Please dismantle the cooler 20、增加温度表 Add a thermometer 21、增加一个工作平台 Add a working platform 22、增加管子马脚 Add pipe fixed supports 23、请更换液压油(滑油) Please change hydraulic oil. 、请更换滑油 Please renew L o 请放气 26、锚机空载试验 No load test of anchor windlass 27、起锚试验 Anchoring test 28、加牛油 Add some grease 29、请更换压力表 To renew the pressure gauge 30、机座反顶加强 To strengthen the engine seat. 31、刹车杆螺纹加油 To lubricate the brake threads 32、离合器(齿轮)加牛油 Add some grease to clutch( gears) 33、更换牛油嘴 Renew the oil nozzle 34、刹车间隙调整 To adjust the brake clearance 35、请检验绞车垫片 Please check the anchor winch washe 36、绞车轴承间隙 Anchor winch bearing clearance 37、绞车旁撑 Anchor winch attached bracket 38、绞车清洁 To clean the anchor winch 39、垫片尺寸不对 The washer size is wrong 40、垫片厚度太薄 The thickness of washers is too thin 41、空载试验 No-load test 42、拉力试验 43、恒涨力试验 Constant expansion test 44、锚与舷板贴合不好 The anchor doesn' t fit the side plate well 45、锚不到位 The anchor hasn't been lowered enough 46、手动(机械)抛锚 Manual( Mechanical) anchoring 47、轴承温度高 The bearing temperature is high 48、液压泵过热 The hydraulic pump is too hot 49、对中不好 The alignment is incorrect 50、锚未收到位 The anchor hasn' t been retaken enough 51、制链器安装提交 The installation of chain stopper to be accepted 52、起(放)锚 Retake( Lower) the anchor 53、收(放)缆 Retake( Lower) the rope ⅨX舵机提交过程用语( for steering gear 1、请检验舵机垫片 Please check the washers of steering gear. 2、请检验舵机旁撑 Please check the steering gear side bracket. 3、舵机安装尺寸 The installation size of steering gear
9 13、振动厉害 The vibration is violent. 14、噪音太大 The decibel(分贝) is too high (The noise is too loud). 15、间隙太大（小） Too much/too little clearance. 16、负荷太重 Overload 17、速度太快 too fast 18、把液压泵盖打开 Please open the hydraulic pump cover. 19、把冷却器拆下 Please dismantle the cooler. 20、增加温度表 Add a thermometer. 21、增加一个工作平台 Add a working platform. 22、增加管子马脚 Add pipe fixed supports. 23、请更换液压油（滑油） Please change hydraulic oil. 24、请更换滑油 Please renew L.O. 25、请放气 Please discharge air. 26、锚机空载试验 No load test of anchor windlass. 27、起锚试验 Anchoring test. 28、加牛油 Add some grease. 29、请更换压力表 To renew the pressure gauge. 30、机座反顶加强 To strengthen the engine seat. 31、刹车杆螺纹加油 To lubricate the brake threads. 32、离合器（齿轮）加牛油 Add some grease to clutch（gears）. 33、更换牛油嘴 Renew the oil nozzle. 34、刹车间隙调整 To adjust the brake clearance. 35、请检验绞车垫片 Please check the anchor winch washers. 36、绞车轴承间隙 Anchor winch bearing clearance. 37、绞车旁撑 Anchor winch attached bracket. 38、绞车清洁 To clean the anchor winch. 39、垫片尺寸不对 The washer size is wrong. 40、垫片厚度太薄 The thickness of washers is too thin. 41、空载试验 No-load test. 42、拉力试验 Pull test. 43、恒涨力试验 Constant expansion test. 44、锚与舷板贴合不好 The anchor doesn’t fit the side plate well. 45、锚不到位 The anchor hasn’t been lowered enough. 46、手动（机械）抛锚 Manual（Mechanical）anchoring. 47、轴承温度高 The bearing temperature is high. 48、液压泵过热 The hydraulic pump is too hot. 49、对中不好 The alignment is incorrect. 50、锚未收到位 The anchor hasn’t been retaken enough. 51、制链器安装提交 The installation of chain stopper to be accepted. 52、起（放）锚 Retake（Lower）the anchor. 53、收（放）缆 Retake（Lower）the rope. Ⅸ.舵机提交过程用语 (for steering gear) 1、请检验舵机垫片 Please check the washers of steering gear. 2、请检验舵机旁撑 Please check the steering gear side bracket. 3、舵机安装尺寸 The installation size of steering gear
4、舵机零位 Nil position of steering gear 5、舵机(1号缸)安全阀 Safety valve for steering gear(NO. I cylinder) 6、压力偏高(低)The pressur gh(low) 7、跑舵 The rudder angle 8、低油位报警 Low oil level alarm 0、电动机加牛油Add ll、手动(自动)操舵 Manual(au 12、单(双)泵操舵 Steering by single(win)pump. 13、泵组对中提交 The alignment of pump set to be approved. 14、拉杆弯曲 Pull rod bendi 15、牛油泵漏油 16、温度表松动 17、压力表损坏 The pressure gauge is damaged 18、0°到左(右)舷35° Nil to port( (starboard)35° 19、左舷到35°右舷35°Port35° to starboard35° X.救生艇提交过程提交 1、艇架(救生艇)强度试验 The strength test for davit(life-boat) 2、收(放)艇 3、遥控放艇 boat lowering by remote control 自动脱钩 Unhook automatically 6、电器限位不好 he limiting switch of the appliance doesnt work. 7、电器限位不同步 The limiting switch of the appliance is not synchronous 8、电器限位调整 Adjust the limiting switch of the appliance 9、起艇机二级启动不好 The two-stage boat lifter doesnt start successfully. 10、请动车 Please start 11、艇架反顶加强 Strengthen the davit from underside. 12、保险杆不活络 The safety lever is not flexible 13、修整 Make an adjustment. 14、轴封漏油 Shaft tunnel oil leakage Ⅺ.舷梯、引水员梯、软梯、吊车、风车等提交过程用语 i (for gangway, pilot ladder, rope ladder, derrick, blower etc.) 舷梯(引水员梯)强度试验 The strength test for gangway( pilot ladder) 2、艇梯(引水员梯/引水员软梯)收放试验 The operating test for pilot ladder (pilot ladder/ pilot rope ladder 3、装好扶手杆 To install the handrails 4、软梯绞车 Rope ladder winch 5、满(空)载Fu(No)-load. 6、吊车空载(强度)试验 The no load( strength) test for derrick 7、安全阀试验 The safety valve test 8、限位试验 The limiting switch test 9、垃圾吊(货舱吊/软管吊)强度试验 The strength test for rubbish derrick (cargo derrick/hose derrick)
10 4、舵机零位 Nil position of steering gear. 5、舵机（1 号缸）安全阀 Safety valve for steering gear（NO.1 cylinder）. 6、压力偏高（低） The pressure is too high (low). 7、跑舵 The rudder angle is out of control. 8、低油位报警 Low oil level alarm. 9、漏油 Oil leakage. 10、电动机加牛油 Add some grease to motor. 11、手动 (自动) 操舵 Manual（auto）steering. 12、单（双）泵操舵 Steering by single (twin) pump. 13、泵组对中提交 The alignment of pump set to be approved. 14、拉杆弯曲 Pull rod bending. 15、牛油泵漏油 Grease pump leakage. 16、温度表松动 The thermometer is loosened. 17、压力表损坏 The pressure gauge is damaged. 18、0°到左 (右)舷 35° Nil to port (starboard) 35°. 19、左舷到 35°右舷 35° Port 35°to starboard 35°. Ⅹ.救生艇提交过程提交 1、艇架（救生艇）强度试验 The strength test for davit（life-boat）. 2、收（放）艇 boat retaking（lowering）. 3、遥控放艇 boat lowering by remote control. 4、自动脱钩 Unhook automatically. 5、再做一次 Do it once again. 6、电器限位不好 The limiting switch of the appliance doesn’t work. 7、电器限位不同步 The limiting switch of the appliance is not synchronous. 8、电器限位调整 Adjust the limiting switch of the appliance. 9、起艇机二级启动不好 The two-stage boat lifter doesn’t start successfully. 10、请动车 Please start. 11、艇架反顶加强 Strengthen the davit from underside. 12、保险杆不活络 The safety lever is not flexible. 13、修整 Make an adjustment. 14、轴封漏油 Shaft tunnel oil leakage. Ⅺ.舷梯、引水员梯、软梯、吊车、风车等提交过程用语 （for gangway, pilot ladder, rope ladder, derrick, blower etc.） 1、舷梯（引水员梯）强度试验 The strength test for gangway（pilot ladder）. 2、艇梯（引水员梯 / 引水员软梯）收放试验 The operating test for pilot ladder（pilot ladder / pilot rope ladder）. 3、装好扶手杆 To install the handrails. 4、软梯绞车 Rope ladder winch. 5、满（空）载 Full (No)-load. 6、吊车空载（强度）试验 The no load ( strength) test for derrick. 7、安全阀试验 The safety valve test. 8、限位试验 The limiting switch test. 9、垃圾吊（货舱吊 / 软管吊）强度试验 The strength test for rubbish derrick（cargo derrick /hose derrick）