Molecular Biology Problem Solver: A Laboratory Guide. Edited by Alan S Gerstein opyright◎2001 ISBNS:0-471-37972-7( Paper);0-47 (Electronic) Nucleotides, Oligonucleotides, and Polynucleotides Alan S Gerstein 268 Nomenclature: De facto and Du jour What Makes a Nucleotide pure? 269 Are Solution Nucleotides Always More Pure Than Lyophilized Nucleotides 269 Are Solution Nucleotides More Stable Than Lyophilized Nucleotides? 270 Does Your Application Require Extremely Pure Nucleotides? 272 How Can You Monitor Nucleotide Purity and Degradation 272 The author would like to thank Anita Gradowski of Pierce Milwaukee for contributing such thorough and helpful information regarding the preparation of nucleotide solutions. Special thanks also to Cica Minetti and David Remeta of Rutgers University for discussing a method to calculate the extinction coefficient of an oligonucleotide. The contributions to this chapter by Howard Coyer and Thomas Tyre, also of Pierce Milwaukee are too numerous to list 267
267 10 Nucleotides, Oligonucleotides, and Polynucleotides Alan S. Gerstein Nucleotides . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 268 Nomenclature: De facto and Du jour . . . . . . . . . . . . . . . . . . 268 What Makes a Nucleotide Pure? . . . . . . . . . . . . . . . . . . . . . . . 269 Are Solution Nucleotides Always More Pure Than Lyophilized Nucleotides?. . . . . . . . . . . . . . . . . . . . . . . . . . . . 269 Are Solution Nucleotides More Stable Than Lyophilized Nucleotides? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 270 Does Your Application Require Extremely Pure Nucleotides? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 272 How Can You Monitor Nucleotide Purity and Degradation?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 272 The author would like to thank Anita Gradowski of Pierce Milwaukee for contributing such thorough and helpful information regarding the preparation of nucleotide solutions. Special thanks also to Cica Minetti and David Remeta of Rutgers University for discussing a method to calculate the extinction coefficient of an oligonucleotide. The contributions to this chapter by Howard Coyer and Thomas Tyre, also of Pierce Milwaukee, are too numerous to list. Molecular Biology Problem Solver: A Laboratory Guide. Edited by Alan S. Gerstein Copyright © 2001 by Wiley-Liss, Inc. ISBNs: 0-471-37972-7 (Paper); 0-471-22390-5 (Electronic)
How Should You Prepare, Quantitate, and Adjust the PH of Small and Large volumes of Nucleotides? 273 What ls the Effect of Thermocycling on Nucleotide Is There a difference between absorbance, A260, and Optical Density? 275 Why Do A260 Unit Values for Single-Stranded DNA and Oligonucleotides Vary in the Research Literature? 278 279 How Pure an ol Application? 279 What Are the Options for Quantitating Oligonucleotides 279 What ls the Storage Stability of Oligonucleotides? Your Vial of Oligonucleotide ls Empty, or ls It? 28 Synthetic Polynucleotides Is a Polynucleotide ldentical to an Oligonucleotide 28 How Are Polynucleotides Manufactured and How Might This Affect your research? 282 Would the World Be a Better Place If Polymer Length Never varied? Oligonucleotides Don't Suffer from Batch to Batch Size Variation. Why Not ow Many Micrograms of Polynucleotide Are in Your Vial? Is It possible to determine the Molecular Weight of a Polynucleotide? 285 What Are the Strategies for Preparing Polymer Solutions of Known concentration 285 Your Cuvette has a 10mm Path Length what Absorbance values Would be observed for the same Why Not Weigh out a portion of the polymer Instead..286 Solution If Your Cuvette Had a 5mm Path Length of Dissolving the Entire Contents of the Vial Is a Phosphate Group Present at the 5 End of ynthetic Nucleic Acid Polym ner What Are the Options for Preparing and Storing Solutions of Nucleic Acid Polymers? Bibliography NUCLEOTIDES Nomenclature: De facto and Du jour Lehninger (1975) provides a thorough discussion of prope nucleotide nomenclature and abbreviations. Unfortunately, 268 Gerstein
How Should You Prepare, Quantitate, and Adjust the pH of Small and Large Volumes of Nucleotides? . . . . . . . . . . . 273 What Is the Effect of Thermocycling on Nucleotide Stability?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 275 Is There a Difference between Absorbance, A260, and Optical Density? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 275 Why Do A260 Unit Values for Single-Stranded DNA and Oligonucleotides Vary in the Research Literature? . . . . . . 278 Oligonucleotides . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 279 How Pure an Oligonucleotide Is Required for Your Application?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 279 What Are the Options for Quantitating Oligonucleotides? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 279 What Is the Storage Stability of Oligonucleotides?. . . . . . . . 280 Your Vial of Oligonucleotide Is Empty, or Is It? . . . . . . . . . . . 281 Synthetic Polynucleotides. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 281 Is a Polynucleotide Identical to an Oligonucleotide?. . . . . . . 281 How Are Polynucleotides Manufactured and How Might This Affect Your Research? . . . . . . . . . . . . . . . . . . . . . . . . . . 282 Would the World Be a Better Place If Polymer Length Never Varied? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 284 Oligonucleotides Don’t Suffer from Batch to Batch Size Variation. Why Not? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 284 How Many Micrograms of Polynucleotide Are in Your Vial? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 284 Is It Possible to Determine the Molecular Weight of a Polynucleotide? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 285 What Are the Strategies for Preparing Polymer Solutions of Known Concentration? . . . . . . . . . . . . . . . . . . . . . . . . . . 285 Your Cuvette Has a 10mm Path Length. What Absorbance Values Would Be Observed for the Same Solution If Your Cuvette Had a 5mm Path Length? . . . . . 286 Why Not Weigh out a Portion of the Polymer Instead of Dissolving the Entire Contents of the Vial?. . . . . . . . . . 287 Is a Phosphate Group Present at the 5¢ End of a Synthetic Nucleic Acid Polymer? . . . . . . . . . . . . . . . . . . . . . 287 What Are the Options for Preparing and Storing Solutions of Nucleic Acid Polymers? . . . . . . . . . . . . . . . . . . 287 Bibliography . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 288 NUCLEOTIDES Nomenclature: De facto and Du jour Lehninger (1975) provides a thorough discussion of proper nucleotide nomenclature and abbreviations. Unfortunately, 268 Gerstein
commercial catalogs and occasionally the research literature troduce different notations. Some consider"NTP"a general term for deoxynucleotides, but the absence of the letter"d"indicates a ribonucleotide to others Commercial literature also describes ribonucleotides as“"RTP's” If the letter“d” Is present, the name describes a deoxynucleotide. If"d"is absent, check the literature piece closely to avoid a common purchasing error. Dideoxynu cleotides are generically referred to as"ddNTPs. What Makes a Nucleotide pure? Using dATP as an example, what categories of impurities could be present? One potential contaminant is a nucleotide other than dATP, such as dCTP. A second class of impurity could be the mono-, di-, or tetraphosphate form of the deoxyadenosine nucleotide. Since most if not all commercial nucleotides are chem. ically synthesized from highly analyzed precursors, contamination with a nucleotide not based on deoxyadenosine is very unlikely a third class of impurities is the non-UV-absorbing organic and inorganic salts accumulated during the synthesis and purification p ocedures While essentially all commercial nucleotides are chemically synthesized, the final products are not necessarily identical Manufacturing processes vary; raw materials and intermediates of the nucleotide synthesis reactions are subjected to different purification strategies and processes. It is these intermediate eps, and the scrutiny of the products' final specifications, that allow manufacturers to legitimately claim that nucleotides are extremely pure A formal definition of extremely pure does not exist, but com- mercial preparations of such products typically contain greater than 99% of the desired nucleotide in the triphosphate form Contaminating nucleotides are rarely detected in commercial preparations, even using exceedingly stringent high-performance chromatography procedures, but some contaminants escape HPLC detection. Freedom from non-UV-absorbing materials is typically judged by comparison of a measured molar extinction (Am) coefficient to published extinction coefficients (E)values Nuclear magnetic resonance(NMR) may also be used to monitor for contaminants such as pyrophosphate Are Solution Nucleotides always More Pure Than Lyophilized Nucleotides? Nucleotides were first made commercially available as solvent precipitated powders. The lyophilized and extremely pure solution Nucleotides, Oligonucleotides, and Polynucleotides 269
commercial catalogs and occasionally the research literature introduce different notations. Some consider “NTP” a general term for deoxynucleotides, but the absence of the letter “d” indicates a ribonucleotide to others. Commercial literature also describes ribonucleotides as “RTP’s.” If the letter “d” is present, the name describes a deoxynucleotide. If “d” is absent, check the literature piece closely to avoid a common purchasing error. Dideoxynucleotides are generically referred to as “ddNTP’s.” What Makes a Nucleotide Pure? Using dATP as an example, what categories of impurities could be present? One potential contaminant is a nucleotide other than dATP, such as dCTP. A second class of impurity could be the mono-, di-, or tetraphosphate form of the deoxyadenosine nucleotide. Since most if not all commercial nucleotides are chemically synthesized from highly analyzed precursors, contamination with a nucleotide not based on deoxyadenosine is very unlikely. A third class of impurities is the non-UV-absorbing organic and inorganic salts accumulated during the synthesis and purification procedures. While essentially all commercial nucleotides are chemically synthesized, the final products are not necessarily identical. Manufacturing processes vary; raw materials and intermediates of the nucleotide synthesis reactions are subjected to different purification strategies and processes. It is these intermediate steps, and the scrutiny of the products’ final specifications, that allow manufacturers to legitimately claim that nucleotides are extremely pure. A formal definition of extremely pure does not exist, but commercial preparations of such products typically contain greater than 99% of the desired nucleotide in the triphosphate form. Contaminating nucleotides are rarely detected in commercial preparations, even using exceedingly stringent high-performance chromatography procedures, but some contaminants escape HPLC detection. Freedom from non-UV-absorbing materials is typically judged by comparison of a measured molar extinction (Am) coefficient to published extinction coefficients (e)values. Nuclear magnetic resonance (NMR) may also be used to monitor for contaminants such as pyrophosphate. Are Solution Nucleotides Always More Pure Than Lyophilized Nucleotides? Nucleotides were first made commercially available as solventprecipitated powders.The lyophilized and extremely pure solution Nucleotides, Oligonucleotides, and Polynucleotides 269
forms appeared in the early 1980s. Some lyophilized preparations approach 98% purity or more but rarely match the >99% achieved by extremely pure solutions. Generally, solution nucleotides are purer than the lyophilized version, but unless supporting quality control data are provided, it should not be concluded that a solution nucleotide is extremely pure or even more pure than a yophilized preparation Are Solution Nucleotides More Stable Than Lyophilized Nucleotides? Peparations of deoxynucleoside triphosphates decompose into nucleoside di- and tetraphosphates via a disproportionation reaction. This reaction is concentration and temperature dependent. At temperatures above 4oC, lyophilized prepara- tions of deoxynucleotides undergo disproportionation faster than nucleotides in solution. In contrast, the rate of degradation for both forms is less than 1% per year at -20oC and below(Table 10.1). Solutions of dideoxynucleotides and ribonucleotides are similarly stable for many months at temperatures of -20C and below. Most, but not all, dideoxy- and ribonucleotides are stable for many months at4°C Table 10. I Storage Stability of Nucleotides Triphosphate Form Months 70°C 2 dATP 99.14 9747 95.46 3945 (275) (1.75) dTTP 97.2 9428 3945 (30mo) (2.75mo) duTP NA NA NA Solution (100mM) dATP 98.75 91.8 (2mo) 37.07 dCTP 9938 (2mo) 21.25 270 Gerstein
forms appeared in the early 1980s. Some lyophilized preparations approach 98% purity or more but rarely match the >99% achieved by extremely pure solutions. Generally, solution nucleotides are purer than the lyophilized version, but unless supporting quality control data are provided, it should not be concluded that a solution nucleotide is extremely pure or even more pure than a lyophilized preparation. Are Solution Nucleotides More Stable Than Lyophilized Nucleotides? Peparations of deoxynucleoside triphosphates decompose into nucleoside di- and tetraphosphates via a disproportionation reaction. This reaction is concentration and temperature dependent. At temperatures above 4°C, lyophilized preparations of deoxynucleotides undergo disproportionation faster than nucleotides in solution. In contrast, the rate of degradation for both forms is less than 1% per year at -20°C and below (Table 10.1). Solutions of dideoxynucleotides and ribonucleotides are similarly stable for many months at temperatures of -20°C and below. Most, but not all, dideoxy- and ribonucleotides are stable for many months at 4°C. 270 Gerstein Table 10.1 Storage Stability of Nucleotides % Triphosphate Form Months -70°C -20°C 4°C 21°C Powder dATP 54 99.44 99.14 97.47 93.93 (48 mo) 97.78 (3 mo) dCTP 54 98.46 95.46 39.3 39.45 (33 mo) (2.75) dGTP 54 96.95 95.37 25.74 34.4 (27 mo) (1.75) dTTP 54 97.29 94.28 27.4 39.45 (30 mo) (2.75mo) dUTP N.A. N.A. N.A. N.A. N.A. Solution (100 mM) dATP 54 99.2 98.75 95.3 91.8 (2 mo) 37.07 (39 mo) dCTP 54 99.38 99.15 96.98 95.2 (2 mo) 21.25 (42 mo)
Table 10.(Continued) %o Triphosphate Form Months Powder dgTP 9883 95.47 0.5 dTTP 98.87 duTP 98.02 71.55 90.1 40.13(6mo) Solution(10mM) dATP 9968 dcTP 982 9885(2mo 98.6 9951 dTTP 93.57 9929 dUTP 93.8 9945 (12mo) 98.5(2mo Solution ddNTP(10mM) ddATP 99.69 94.52 ddCTP 984 94. 9936 Solution ddNTP(5mM) ddATP 68.56 9963 ddcTP 100 ddGTP 34343 96.67 ddTTP RTP Solutions(100mM) ATP 9857 98.18 95.39 CTP 333 99 98.43 GTP 9846 98.44 96.82 UTP 9971 Source: Data aration of nucleotide species via high perfor on an Amersham Pharmacia Biotech FPLCe Syster Notes: Each umoles(0. 2 ml of a 1 mM solution) was injected onto a Mono QB Ion Exchange column Using the following buffers: Buffer A, 5mM sodium phosphate, PH 7.0 Buffer B, 5mM sodium phosphate, IM NaCl PH 7.0. trification was achieved via a gradient of 5-35% NaCl over 15 minutes using a flow rate Nucleotides, Oligonucleotides, and Polynucleotides 271
Nucleotides, Oligonucleotides, and Polynucleotides 271 Table 10.1 (Continued) % Triphosphate Form Months -70°C -20°C 4°C 21°C Powder dGTP 54 99.63 98.83 95.47 90.5 (2 mo) 19.7 (42 mo) dTTP 54 99.44 98.87 93.54 95.6 (2 mo) 0.07 (42) dUTP 54 99.23 98.02 71.55 90.1 (1.2mo) 40.13 (6mo) Solution (10 mM) dATP 15 99.68 99.59 88.6 (12 mo) 98.5 (2 mo) dCTP 15 98.2 99.56 86.11 (12 mo) 98.85 (2mo) dGTP 15 98.6 99.51 89.47 (12 mo) 98.35 (2mo) dTTP 15 93.57 99.29 81.05 (12 mo) 98.86 (2mo) dUTP 15 93.8 99.45 84.95 (12 mo) 98.5 (2mo) Solution ddNTP (10 mM) ddATP 3 99.69 99.49 94.52 ddCTP 3 100 98.51 97.38 ddGTP 3 98.4 98.08 94.23 ddTTP 3 99.36 99.13 87.06 Solution ddNTP (5 mM) ddATP 3 99.77 98.12 68.56 4 99.63 96.31 2 ddCTP 3 98.77 100 98.4 4 99.27 99.46 93.72 ddGTP 3 95.61 98 96.67 4 98.25 97.9 93.68 ddTTP 3 93.1 55.09 49.03 4 94.25 63.23 3.6 RTP Solutions (100 mM) ATP 3 98.57 98.18 95.39 CTP 3 99.25 99.43 98.43 GTP 3 98.46 98.44 96.82 UTP 3 99.71 99.69 97.99 Source: Data based on chromatographic separation of nucleotide species via high performance chromatography on an Amersham Pharmacia Biotech FPLC® System. Notes: Each sample, 0.2mmoles (0.2 ml of a 1 mM solution) was injected onto a Mono Q® Ion Exchange column. Using the following buffers: Buffer A, 5mM sodium phosphate, pH 7.0. Buffer B, 5mM sodium phosphate, 1M NaCl, pH 7.0. purification was achieved via a gradient of 5–35% NaCl over 15 minutes using a flow rate of 1 ml/min. Nucleotide peaks were detected at of 254 nm. (Data from Amersham Pharmacia Biotech, 1993a.)