a B: The second Law of Thermodynamics [AW 42-50: VN Chapter 5; VwB&S-6.3, 6.4, Chapter 7 1. B. Concept and statements of the Second law why do we need a second law?) The unrestrained expansion, or the temperature equilibration of the two bricks, are familiar processes. Suppose you are asked whether you have ever seen the reverse of these processes take lace? Do two bricks at a medium temperature ever go to a state where one is hot and one is cold? will the gas in the unrestrained expansion ever spontaneously return to occupying only the left side of the volume? Experience hints that the answer is no. However, both these processes, unfamiliar their occurrence. There the mpatible with the first law. In other words the first law does not prohibit though they may be, are co lus must be some other"great principle"that describes the direction of natural processes, that tells us which first law compatible processes will not be observed. This contained in the second law. Like the first law, it is a generalization from an enormous amount of observation There are several ways in which the second law of thermodynamics can be stated. Listed below are three that are often encountered. As described in class(and as derived in almost every thermodynamics textbook), although the three may not appear to have much connection with each other they are equivalent 1)No process is possible whose sole result is the absorption of heat from a reservoir and the conversion of this heat into work. [Kelvin-Planck statement of the second law] Q System w This is not possible 2) No process is possible whose sole result is the transfer of heat from a cooler to a hotter Clausius statement of the second law Q For T<T2, this is not possible 1B-1
1.B: The Second Law of Thermodynamics [IAW 42-50; VN Chapter 5; VWB&S-6.3, 6.4, Chapter 7] 1.B.1 Concept and Statements of the Second Law (Why do we need a second law?) The unrestrained expansion, or the temperature equilibration of the two bricks, are familiar processes. Suppose you are asked whether you have ever seen the reverse of these processes take place? Do two bricks at a medium temperature ever go to a state where one is hot and one is cold? Will the gas in the unrestrained expansion ever spontaneously return to occupying only the left side of the volume? Experience hints that the answer is no. However, both these processes, unfamiliar though they may be, are compatible with the first law. In other words the first law does not prohibit their occurrence. There thus must be some other “great principle” that describes the direction of natural processes, that tells us which first law compatible processes will not be observed. This is contained in the second law. Like the first law, it is a generalization from an enormous amount of observation. There are several ways in which the second law of thermodynamics can be stated. Listed below are three that are often encountered. As described in class (and as derived in almost every thermodynamics textbook), although the three may not appear to have much connection with each other, they are equivalent. 1) No process is possible whose sole result is the absorption of heat from a reservoir and the conversion of this heat into work. [Kelvin-Planck statement of the second law] Q System T2 W This is not possible T1 2) No process is possible whose sole result is the transfer of heat from a cooler to a hotter body. [Clausius statement of the second law] Q T2 T1 For T1 < T2 , this is not possible Q 1B-1
3)There exists a property called entropy, S, which is a thermodynamic property of a system. For a reversible process, changes in this property are given by ds=(do T The entropy change of any system and its surroundings, considered together, is positive and approaches zero for any process which approaches reversibility Atotal≥0 For an isolated system, i.e., a system that has no interaction with the surroundings, changes in the system have no effect on the surroundings. In this case, we need to consider the system only, and the first and second laws become AE system=0 △S >0 For an isolated system the total energy (E=U+ Kinetic Energy Potential Energy +...)is constant The entropy can only increase or, in the limit of a reversible process, remain constant All of these statements are equivalent, but ( 3)gives a direct, quantitative measure of the departure from reversibility Entropy is not a familiar concept and it may be helpful to provide some additional rationale for its appearance. If we look at the first law dU=do-dw the term on the left is a function of state, while the two terms on the right are not. For a simple compressible substance, however, we can write the work done in a reversible process as dw= Pdv so that dU=do- Pdv: First law for a simple compressible substance, reversible process Two out of the three terms in this equation are expressed in terms of state variables. It seems plausible that we ought to be able to express the third term using state variables as well, but what are the appropriate variables? If so, the term dg=([I should perhaps be viewed as analogous to dw Pdv where the parenthesis denotes an intensive state variable and the square bracket denotes extensive state variable. The second law tells us that the intensive variable is the temperature, T, and the extensive state variable is the entropy, s The first law for a simple compressible substance in terms of state variables is thus du= Tds-pdv (B.1.1) Because Eq. (B. 1. 1)includes the second law, it is referred to as the combined first and second law Because it is written in terms of state variables, it is true for all processes, not just reversible ones We list below some attributes of entropy a)S is an extensive variable. The entropy per unit mass, or specific entropy, is s 1B-2
3) There exists a property called entropy, S, which is a thermodynamic property of a system. For a reversible process, changes in this property are given by dS = (dQreversible)/T The entropy change of any system and its surroundings, considered together, is positive and approaches zero for any process which approaches reversibility. ∆Stotal > 0 For an isolated system, i.e., a system that has no interaction with the surroundings, changes in the system have no effect on the surroundings. In this case, we need to consider the system only, and the first and second laws become: ∆E system = 0 ∆S system > 0 For an isolated system the total energy (E = U + Kinetic Energy + Potential Energy + ....) is constant. The entropy can only increase or, in the limit of a reversible process, remain constant. All of these statements are equivalent, but (3) gives a direct, quantitative measure of the departure from reversibility. Entropy is not a familiar concept and it may be helpful to provide some additional rationale for its appearance. If we look at the first law, dU = dQ − dW the term on the left is a function of state, while the two terms on the right are not. For a simple compressible substance, however, we can write the work done in a reversible process as dW = PdV , so that dU = dQ − PdV ; First law for a simple compressible substance, reversible process. Two out of the three terms in this equation are expressed in terms of state variables. It seems plausible that we ought to be able to express the third term using state variables as well, but what are the appropriate variables? If so, the term dQ = ( ) [ ] should perhaps be viewed as analogous to dW = PdV where the parenthesis denotes an intensive state variable and the square bracket denotes an extensive state variable. The second law tells us that the intensive variable is the temperature, T, and the extensive state variable is the entropy, S. The first law for a simple compressible substance in terms of state variables is thus dU = TdS − PdV . (B.1.1) Because Eq. (B.1.1) includes the second law, it is referred to as the combined first and second law. Because it is written in terms of state variables, it is true for all processes, not just reversible ones. We list below some attributes of entropy: a) S is an extensive variable. The entropy per unit mass, or specific entropy, is s. 1B-2
b) The units of entropy are Joules per degree Kelvin(/K). The units for specific entropy are c) For a system, ds T, where the numerator is the heat given to the system and the denominator is the temperature of the system at the location where the heat is received d)ds=0 for pure work transfer Muddy points Why is_dU= TdS-Pdvalways true?(MP 1B.1 What makes dOre, _ different than dO?(MP 1B.2) 1B.2 Axiomatic Statements of the Laws of Thermodynamics- (i. Introduction As a further aid in familiarization with the second law of thermodynamics and the idea of entropy, we draw an analogy with statements made previously concerning quantities that are closer to experience. In particular, we wish to(re-)present the Zeroth and First laws of thermodynamics in the same framework as we have used for the second law In this so-called"axiomatic formulation" the zeroth first and second laws are all introduced in a similar fashion (ii. Zeroth Law We start with a statement which is based on two observations a) If two bodies are in contact through a thermally-conducting boundary for a sufficiently long time, no further observable changes take place; thermal equilibrium is said to prevail b) Two systems which are individually in thermal equilibrium with a third are in thermal equilibrium with each other; all three systems have the same value of the property called mperature The closely connected ideas of temperature and thermal equilibrium are formally expressed in the Zeroth Law of Thermodynamics Zeroth llaw There exists for every thermodynamic system in equilibrium a property called temperature. Equality of temperature is a necessary and sufficient condition for thermal equilibrium The Zeroth law thus defines a property (temperature)and describes its behavior. Giii.)First Law Observations also show that for any system there is a property called the energy. The First Law asserts that one must associate such a property with every system First law There exists for every thermodynamic system a property called the energy ge of energy of a system is equal to the mechanical work done on the system in an adiabatic process. In a non-adiabatic process, the change in energy is equal to the heat added to the system minus the mechanical work done by the system From notes of Professor F. E C. Culick, California Institute of Technology(with minor changes) 1B-3
b) The units of entropy are Joules per degree Kelvin (J/K). The units for specific entropy are J/K-kg. dQ c) For a system, dS = rev , where the numerator is the heat given to the system and the T denominator is the temperature of the system at the location where the heat is received. d) dS = 0 for pure work transfer. Muddy points Why is dU = TdS − PdV always true? (MP 1B.1) What makes dQrev different than dQ? (MP 1B.2) 1.B.2 Axiomatic Statements of the Laws of Thermodynamics 1 (i.) Introduction As a further aid in familiarization with the second law of thermodynamics and the idea of entropy, we draw an analogy with statements made previously concerning quantities that are closer to experience. In particular, we wish to (re-) present the Zeroth and First Laws of thermodynamics in the same framework as we have used for the Second Law. In this so-called "axiomatic formulation", the Zeroth, First and Second Laws are all introduced in a similar fashion. (ii.) Zeroth Law We start with a statement which is based on two observations: a) If two bodies are in contact through a thermally-conducting boundary for a sufficiently long time, no further observable changes take place; thermal equilibrium is said to prevail. b) Two systems which are individually in thermal equilibrium with a third are in thermal equilibrium with each other; all three systems have the same value of the property called temperature. The closely connected ideas of temperature and thermal equilibrium are formally expressed in the “Zeroth Law of Thermodynamics”: Zeroth Law There exists for every thermodynamic system in equilibrium a property called temperature. Equality of temperature is a necessary and sufficient condition for thermal equilibrium. The Zeroth law thus defines a property (temperature) and describes its behavior. (iii.) First Law Observations also show that for any system there is a property called the energy. The First Law asserts that one must associate such a property with every system. First Law There exists for every thermodynamic system a property called the energy. The change of energy of a system is equal to the mechanical work done on the system in an adiabatic process. In a non-adiabatic process, the change in energy is equal to the heat added to the system minus the mechanical work done by the system. 1 From notes of Professor F. E. C. Culick, California Institute of Technology (with minor changes) 1B-3
propem an the basis of experimental results, therefore, one is led to assert the existence of two new similar way, a further remarkable relationship between heat and temperature will be established, and a new property, the entropy, defined. Although this is a much less familiar property, it is to be stressed that the general approach is quite like that used to establish the Zeroth and First Laws. A Viewed in this way, the entropy should appear no more mystical than the internal energy. sults increase of entropy in a naturally occurring process is no less real than the conservation of energy Giv. Second Law Although all natural processes must take place in accordance with the First Law, the principle of conservation of energy is, by itself, inadequate for an unambiguous description of the behavior of a system. Specifically, there is no mention of the familiar observation that every natural process has in some sense a preferred direction of action. For example, the flow of heat occurs naturally from hotter to colder bodies, in the absence of other influences, but the reverse flow certainly is not in violation of the First Law. So far as that law is concerned, the initial and final states are symmetrical in a very important respect The Second Law is essentially different from the First Law; the two principles are dependent and cannot in any sense be deduced from one another. Thus, the concept of energy is not sufficient, and a new property must appear. This property can be developed, and the Second Law introduced, in much the same way as the Zeroth and First Laws were presented. By examination of certain observational results, one attempts to extract from experience a law which is supposed to be general; it is elevated to the position of a fundamental axiom to be proved or disproved by subsequent experiments. Within the structure of classical thermodynamics, there is no proof more fundamental than observations. A statement which can be adopted as the Second law of thermodynamics Second law There exists for every thermodynamic system in equilibrium an extensive scalar property called the entropy S, such that in an infinitesimal reversible change of state of the system, ds=doT, where T is the absolute temperature and d@ is the amount of heat received by the system. The entropy of a thermally insulated system cannot decrease and is constant if and only if all processes are reversible As with the Zeroth and First Laws, the existence of a new property is asserted and its behavior is described (v. Reversible Processes we can recall the definition, a process is called completely reversible if, after the process has ' and In the course of this development, the idea of a completely reversible process is central occurred, both the system and its surroundings can be wholly restored by any means to their respective initial states ". Especially, it is to be noted that the definition does not in this form, specify that the reverse path must be identical with the forward path. If the initial states can be restored by any means whatever, the process is by definition completely reversible. If the paths are identical, then one usually calls the process (of the system) reversible, or one may say that the state of the system follows a reversible path. In this path(between two equilibrium states I and 2) (i) the system passes through the path followed by the equilibrium states only, and (ii) the system will take the reversed path 2 to l by a simple reversal of the work done and heat added reversible processes are idealizations not actually encountered. However, they are clearly 1B-4
On the basis of experimental results, therefore, one is led to assert the existence of two new properties, the temperature and internal energy, which do not arise in ordinary mechanics. In a similar way, a further remarkable relationship between heat and temperature will be established, and a new property, the entropy, defined. Although this is a much less familiar property, it is to be stressed that the general approach is quite like that used to establish the Zeroth and First Laws. A general principle and a property associated with any system are extracted from experimental results. Viewed in this way, the entropy should appear no more mystical than the internal energy. The increase of entropy in a naturally occurring process is no less real than the conservation of energy. (iv.) Second Law Although all natural processes must take place in accordance with the First Law, the principle of conservation of energy is, by itself, inadequate for an unambiguous description of the behavior of a system. Specifically, there is no mention of the familiar observation that every natural process has in some sense a preferred direction of action. For example, the flow of heat occurs naturally from hotter to colder bodies, in the absence of other influences, but the reverse flow certainly is not in violation of the First Law. So far as that law is concerned, the initial and final states are symmetrical in a very important respect. The Second Law is essentially different from the First Law; the two principles are independent and cannot in any sense be deduced from one another. Thus, the concept of energy is not sufficient, and a new property must appear. This property can be developed, and the Second Law introduced, in much the same way as the Zeroth and First Laws were presented. By examination of certain observational results, one attempts to extract from experience a law which is supposed to be general; it is elevated to the position of a fundamental axiom to be proved or disproved by subsequent experiments. Within the structure of classical thermodynamics, there is no proof more fundamental than observations. A statement which can be adopted as the Second Law of thermodynamics is: Second Law There exists for every thermodynamic system in equilibrium an extensive scalar property called the entropy, S, such that in an infinitesimal reversible change of state of the system, dS = dQ/T, where T is the absolute temperature and dQ is the amount of heat received by the system. The entropy of a thermally insulated system cannot decrease and is constant if and only if all processes are reversible. As with the Zeroth and First Laws, the existence of a new property is asserted and its behavior is described. (v.) Reversible Processes In the course of this development, the idea of a completely reversible process is central, and we can recall the definition, “a process is called completely reversible if, after the process has occurred, both the system and its surroundings can be wholly restored by any means to their respective initial states”. Especially, it is to be noted that the definition does not, in this form, specify that the reverse path must be identical with the forward path. If the initial states can be restored by any means whatever, the process is by definition completely reversible. If the paths are identical, then one usually calls the process (of the system) reversible, or one may say that the state of the system follows a reversible path. In this path (between two equilibrium states 1 and 2), (i) the system passes through the path followed by the equilibrium states only, and (ii) the system will take the reversed path 2 to 1 by a simple reversal of the work done and heat added. Reversible processes are idealizations not actually encountered. However, they are clearly 1B-4
useful idealizations. For a process to be completely reversible, it is necessary that it be quasi-static and that there be no dissipative influences such as friction and diffusion. The precise(necessary and sufficient) condition to be satisfied if a process is to be reversible is the second part of the Second The criterion as to whether a process is completely reversible must be based on the initial and final states. In the form presented above, the Second Law furnishes a relation between the properti defining the two states, and thereby shows whether a natural process connecting the states is Muddy points What happens when all the energy in the universe is uniformly spread, ie, entropy at a maximum?(MP 1B 1. B3 Combined first and Second law expressions First law. du=dQ-dw- Always true Work and heat exchange in terms of state variables dQ=Tds; dw= Pdv -Only true for reversible processes dU=do-Pdv Simple compressible substance, reversible process du=d@-- Xdr Substance with other work modes(e. g, stress-strain), X is a pressure-like quantity, y is a volume like quantity dU= Tds-dw; Only true for a reversible process First law in terms of state variables dU=Tas-Pav: This is a relation between properties and is always true In terms of specific quantities(per unit mass) du= tds -pdl Combined first and second law(a)or Gibbs equation(a) The combined first and second law expressions are often more usefully written in terms of the enthalpy, or specific enthalpy, h=u+ Pv dh= du t pdv+vd Tds -Pdv+ pdv vdP the first law dh= tds vdP since v=l/p dh= tds t Combined first and second law()or Gibbs equation(b) In terms of enthalpy (rather than specific enthalpy) the relation is dH=TdS vaP 1B-5
hu ρ useful idealizations. For a process to be completely reversible, it is necessary that it be quasi-static and that there be no dissipative influences such as friction and diffusion. The precise (necessary and sufficient) condition to be satisfied if a process is to be reversible is the second part of the Second Law. The criterion as to whether a process is completely reversible must be based on the initial and final states. In the form presented above, the Second Law furnishes a relation between the properties defining the two states, and thereby shows whether a natural process connecting the states is possible. Muddy points What happens when all the energy in the universe is uniformly spread, ie, entropy at a maximum? (MP 1B.3) 1.B.3 Combined First and Second Law Expressions First Law: dU = dQ − dW - Always true Work and heat exchange in terms of state variables: dQ = TdS; dW = PdV - Only true for reversible processes. dU = dQ − PdV ; Simple compressible substance, reversible process dU = dQ − PdV − XdY ; Substance with other work modes (e.g., stress-strain), X is a pressure-like quantity, Y is a volume like quantity dU = TdS − dW ; Only true for a reversible process First law in terms of state variables: dU = TdS − PdV ; This is a relation between properties and is always true In terms of specific quantities (per unit mass): du = Tds − Pdv Combined first and second law (a) or Gibbs equation (a) The combined first and second law expressions are often more usefully written in terms of the enthalpy, or specific enthalpy, =+ Pv: dh = du + Pdv + vdP = Tds − Pdv + Pdv + vdP , using the first law. dh = Tds + vdP Or, since v = 1/ ρ dP dh = Tds + . Combined first and second law (b) or Gibbs equation (b) In terms of enthalpy (rather than specific enthalpy) the relation is dH = TdS + VdP . 1B-5