《PTC 全球服务》（第一册）PDF电子书

DPTC PTc全球服务 ProlENGINEER Wildfire 快速入门 T994-33001

PTC 全球服务 Pro/ENGINEER Wildfire 快速入门 T994-330-01

PTC 培训日程 Pro/ ENGINEER Wildfire快速入门 第1天 Pro/ENGINEER Wildfire入门 编辑设计模型 创建参照几何 创建直接特征 第2天 使用“草绘器”来捕捉设计意图 创建基于草绘的特征I 创建基于草绘的特征 第3天 复制设计模型特征 强化设计模型 元件 第4天 创建机构连接 创建绘图 解决再生失败 项目Ⅲ 第5天 管理组件 分析和优化设计模型 项目ⅣV

培训日程 Pro/ENGINEER Wildfire 快速入门 第 1 天 Pro/ENGINEER Wildfire 入门 编辑设计模型 创建参照几何 创建直接特征 第 2 天 使用“草绘器”来捕捉设计意图 创建基于草绘的特征 I 创建基于草绘的特征 II 项目 I 第 3 天 复制设计模型特征 强化设计模型 装配元件 项目 II： 第 4 天 创建机构连接 创建绘图 解决再生失败 项目 III 第 5 天 管理组件 分析和优化设计模型 项目 IV

DPTC 目录 Pro/ENG| NEER Wildfire快速入门 THE PRECISION LEARNING METHODOLOGY CONTINUOUS IMPROVEMENT PRECISION LEARNING IN THE CLASSROOM EDUCATION CIRCUIT EXAMPLE INTRODUCTION TO PRO/ENGINEER WILDFIRE Module 1 Lab Exercises Exercise 1: Previewing and Opening Design Models 1-3 Exercise 2: Orienting Design Models 1-8 112 EDITING DESIGN MODELS Module 2 Lab exercises 2-3 Exercise 1: Selecting Components and Features Exercise 2: Editing Design Models Exercise 3: Creating and Managing Layers ..2-16 CREATING REFERENCE GEOMETRY Referencing PTC Help for Module 3 Topics 3-3 Accessing Pro/ENGINEER Wildfire Help Center Module 3 lab exercises 3-5 Exercise 1: Creating Reference Geometry 3-5 Exercise 2: Creating Advanced Reference Geometry. Exercise 3: Creating and Managing Layers Summary CREATING DIRECT FEAT URES Referencing PTC Help for Module 4 Topics 4-3 Accessing Pro/ENGINEER Wildfire Help Center. Module 4 Lab Exercises 4-4 Exercise 1: Creating Direct Features-Holes

目录 Pro/ENGINEER Wildfire 快速入门 THE PRECISION LEARNING METHODOLOGY............................................................................i CONTINUOUS IMPROVEMENT.......................................................................................................ii PRECISION LEARNING IN THE CLASSROOM ...........................................................................iii EDUCATION CIRCUIT EXAMPLE................................................................................................... iv INTRODUCTION TO PRO/ENGINEER WILDFIRE 1-1 Module 1 Lab Exercises .........................................................................................1-3 Exercise 1: Previewing and Opening Design Models.................................................................1-3 Exercise 2: Orienting Design Models ............................................................................................1-8 Summary...............................................................................................................1-12 EDITING DESIGN MODELS 2-1 Module 2 Lab Exercises .........................................................................................2-3 Exercise 1: Selecting Components and Features.......................................................................2-3 Exercise 2: Editing Design Models ................................................................................................2-9 Exercise 3: Creating and Managing Layers...............................................................................2-16 Summary...............................................................................................................2-18 CREATING REFERENCE GEOMETRY 3-1 Referencing PTC Help for Module 3 Topics...........................................................3-3 Accessing Pro/ENGINEER Wildfire Help Center........................................................................3-3 Module 3 Lab Exercises .........................................................................................3-5 Exercise 1: Creating Reference Geometry..................................................................................3-5 Exercise 2: Creating Advanced Reference Geometry .............................................................3-12 Exercise 3: Creating and Managing Layers...............................................................................3-20 Summary...............................................................................................................3-22 CREATING DIRECT FEAT URES 4-1 Referencing PTC Help for Module 4 Topics...........................................................4-3 Accessing Pro/ENGINEER Wildfire Help Center........................................................................4-3 Module 4 Lab Exercises .........................................................................................4-4 Exercise 1: Creating Direct Features – Holes .............................................................................4-4

PTC Exercise 2: Creating Direct Features- Rounds 4-10 Exercise 3: Creating Direct Features-Chamfers Exercise 4: Creating Direct Features- Drafts Exercise 5: Creating Direct Features- Shells 4-31 Exercise 6: Creating and Managing Layers Exercise 7: Creating Direct Features on the Chuck(Challenge) Exercise 8: Creating Direct Features on the Flywheel (Challenge) Exercise 9: Shelling the Engine Cover(Challenge) Exercise 10: Creating Drafts on the Cylinder (Challenge). Summary 4-44 CAPTURING DESIGN INT ENT WITH SKETCHER 5-1 Referencing PTC Help for Module 5 Topics Accessing Pro/ENGINEER Wildfire Help Center Module 5 lab exercises 5-4 Exercise 1: Creating New Design Models Using Default Templates Exercise 2: Capturing Des ign Intent with Sketcher .5-7 Exercise 3: Creating Datum Features( Challenge 5-22 Summary 5-25 CREATING SKETCH-BASED FEATURES I 6-1 Referencing PTC Help for Module 6 Topics .6-3 Accessing Pro/ENGINEER Wildfire Help Center. Module 6 lab exercises Exercise 1: Creating Extruded and revolved Features Exercise 2: Creating Ribs and Group Datum Features.. 6-17 Exercise 3: Completing the Piston( Challenge) .6-22 Summary 6-25 CREATING SKETCH-BASED FEATURES II 7-1 Referencing PTC Help for Module 7 Topics Accessing Pro/ENGINEER Wildfire Help Center Module 7 Lab Exercises Exercise 1: Creating Sweeps EXercise 2: Creating Blends EXercise 3: Sweeping Along a 3-D Trajectory Summary 7-15

Exercise 2: Creating Direct Features – Rounds ....................................................................... 4-10 Exercise 3: Creating Direct Features – Chamfers....................................................................4-21 Exercise 4: Creating Direct Features – Drafts .......................................................................... 4-27 Exercise 5: Creating Direct Features – Shells .......................................................................... 4-31 Exercise 6: Creating and Managing Layers.............................................................................. 4-33 Exercise 7: Creating Direct Features on the Chuck (Challenge)........................................... 4-35 Exercise 8: Creating Direct Features on the Flywheel (Challenge)....................................... 4-37 Exercise 9: Shelling the Engine Cover (Challenge)................................................................ 4-41 Exercise 10: Creating Drafts on the Cylinder (Challenge)..................................................... 4-42 Summary .............................................................................................................. 4-44 CAPTURING DESIGN INTENT WITH SKETCHER 5-1 Referencing PTC Help for Module 5 Topics.......................................................... 5-3 Accessing Pro/ENGINEER Wildfire Help Center ........................................................................5-3 Module 5 Lab Exercises ......................................................................................... 5-4 Exercise 1: Creating New Design Models Using Default Templates .......................................5-4 Exercise 2: Capturing Des ign Intent with Sketcher.....................................................................5-7 Exercise 3: Creating Datum Features (Challenge) .................................................................. 5-22 Summary .............................................................................................................. 5-25 CREATING SKETCH-BASED FEATURES I 6-1 Referencing PTC Help for Module 6 Topics.......................................................... 6-3 Accessing Pro/ENGINEER Wildfire Help Center ........................................................................6-3 Module 6 Lab Exercises ......................................................................................... 6-4 Exercise 1: Creating Extruded and Revolved Features .............................................................6-4 Exercise 2: Creating Ribs and Group Datum Features ........................................................... 6-17 Exercise 3: Completing the Piston (Challenge)........................................................................ 6-22 Summary .............................................................................................................. 6-25 CREATING SKETCH-BASED FEATURES II 7-1 Referencing PTC Help for Module 7 Topics.......................................................... 7-3 Accessing Pro/ENGINEER Wildfire Help Center ........................................................................7-3 Module 7 Lab Exercises ......................................................................................... 7-4 Exercise 1: Creating Sweeps..........................................................................................................7-4 Exercise 2: Creating Blends............................................................................................................7-7 Exercise 3: Sweeping Along a 3-D Trajectory.......................................................................... 7-10 Exercise 4: Creating a Blend Using Grouped Datum Features (Challenge)........................ 7-12 Summary .............................................................................................................. 7-15

DPTC PROJECT I Module 8 Lab exercise 3 Objective 1: Creating the Piston Pin .8-3 Objective 2: Creating the Piston ..8-10 8-15 Objective 5: Creating the Engine Block Objective 6: Creating the Impeller Housing 888 Objective 7: Creating the Frame. DUPLICATING DESIGN MODEL FEATURES Referencing PTC Help for Module 9 Topics 3 Module 9 Lab exercises 9-4 Exercise 1: Patterning Features Exercise 2: Copying Features .9-17 Exercise 3: Mirroring Models. .9-23 Exercise 4: Creating and Managing Layers .9-25 9-27 ENHANCING DESIGN MODELS USING FAMILY TAB LES RELATIONS AND PARAMETERS Referencing PTC Help for Module 10 Topics 10-3 Accessing Pro/ENGINEER Wildfire Help Center 10-3 Module 10 Lab exercises 10-4 Exercise 1: Creating Family Tables .10-4 Exercise 2: Creating Relations Exercise 3: Creating Family Ta 0 Summary .10-15 ASSEMBLING COMPONENTS 111 Referencing PTC Help for Module 11 Topics 11-3 Accessing Pro/ENGINEER Wildfire Help Center Module 11 Lab Exercises 11-4 Exercise 1: Assembling Using Constraints Exercise 2: Assembling Using Component Interfaces. 11-11 Exercise 3: Assembling Flexible Components 11-17 Exercise 4: Assembling Additional Engine Components( Challenge) 11-22

PROJECT I 8-1 Module 8 Lab Exercise...........................................................................................8-3 Objective 1: Creating the Piston_Pin............................................................................................8-3 Objective 2: Creating the Piston....................................................................................................8-5 Objective 3: Creating the Connecting_Rod................................................................................8-10 Objective 4: Creating the Crankshaft..........................................................................................8-15 Objective 5: Creating the Engine Block......................................................................................8-23 Objective 6: Creating the Impeller Housing...............................................................................8-33 Objective 7: Creating the Frame..................................................................................................8-42 Summary...............................................................................................................8-48 DUPLICATING DESIGN MODEL FEATURES 9-1 Referencing PTC Help for Module 9 Topics...........................................................9-3 Accessing Pro/ENGINEER Wildfire Help Center........................................................................9-3 Module 9 Lab Exercises .........................................................................................9-4 Exercise 1: Patterning Features.....................................................................................................9-4 Exercise 2: Copying Features ......................................................................................................9-17 Exercise 3: Mirroring Models ........................................................................................................9-23 Exercise 4: Creating and Managing Layers...............................................................................9-25 Summary...............................................................................................................9-27 ENHANCING DESIGN MODELS USING FAMILY TAB LES, RELATIONS, AND PARAMETERS 10-1 Referencing PTC Help for Module 10 Topics.......................................................10-3 Accessing Pro/ENGINEER Wildfire Help Center......................................................................10-3 Module 10 Lab Exercises .....................................................................................10-4 Exercise 1: Creating Family Tables.............................................................................................10-4 Exercise 2: Creating Relations .....................................................................................................10-9 Exercise 3: Creating Family Tables (Challenge)....................................................................10-14 Summary.............................................................................................................10-15 ASSEMBLING COMPONENTS 11-1 Referencing PTC Help for Module 11 Topics.......................................................11-3 Accessing Pro/ENGINEER Wildfire Help Center......................................................................11-3 Module 11 Lab Exercises .....................................................................................11-4 Exercise 1: Assembling Using Constraints ................................................................................11-4 Exercise 2: Assembling Using Component Interfaces ..........................................................11-11 Exercise 3: Assembling Flexible Components .......................................................................11-17 Exercise 4: Assembling Additional Engine Components (Challenge)................................11-22