J Mater Sci(2007)42:5046-5056 DOI10.1007/s10853-006-0579-5 Microstructural characterization and fracture properties of SiC-based fibers annealed at elevated temperatures J.J.Sha·T. Hinoki·A. Kohyama Received: 6 April 2006/ Accepted: 15 June 2006/Published online: 22 February 2007 Springer Science+Business Media, LLC 2007 Abstract Ceramic matrix composites(CMCs)have Introduction been proposed as potential structural materials for application of high temperature technologies. Excel- Currently, ceramic matrix composites(CMCs)have lent high temperature performance of CMCs requires been proposed as potential structural materials for that fibers must have high enough thermal stability and application of high temperature technologies, such as sufficient mechanical properties throughout the service advanced energy-generation systems and propulsion life. In order to clarify the correlation between the systems [1-3]. The key to successful application of mechanical properties and the microstructure of Sic- CMCs is judicious selection and incorporation of based fibers, Sic-based fibers were annealed at ele- ceramic fiber reinforcement with proper chemical vated temperatures in Ar for 1 h After annealing, the physical and mechanical properties. For high temper- fracture strengths on these fibers were evaluated at ature operation, the most critical fiber properties are room temperature by tensile test; the microstructural high strength and its reliable retention throughout the features were characterized by X-ray diffraction service life. Low fiber strength and thermal stability (XRD) and field emission scanning electron micros- could result in low fracture toughness and accelerate copy(FE-SEM). Furthermore, the fracture mechanics sub-critical crack propagation in CMCs was applied to estimate the fracture toughness and the Recently developed Sic-based fibers witi critical fracture energy of these fibers. As a result, stoichiometric composition and high-crystallite excellent microstructure and mechanical stabilities structure, such as Hi-Nicalon type s [4 and Tyran- were observed for SiC fibers with near-stoichiometric noM-SA [5], are promising reinforcement for CMCs composition and high-crystallite structure Combining fabrication. These fibers experienced a pyrolysis or the microstructure examination with tensile test indi- sintering process during fabrication and their micro- cates that the thermal and mechanical stabilities of Sic structure and mechanical properties depend on the fibers at high temperatures were mainly controlled by thermal history. On the other hand, CMCs may be their crystallization and composition as well as other applied or fabricated above the fiber's processin temperature [1-3, 6, 7. In many cases, SiC fibers were expected to expose to an environment with very high temperature and low oxygen partial pressure in which case, the performance of fibers could be changed by J.Sha(凶) hermal exposure, since the thermal and mechanical International Innovation Center, Kyoto University, stability of Sic fibers, which can vary with processing Sakyo-ku, Kyoto 606-8501, Japan conditions, are very sensitive to high temperature e-mail: shajianjun@iic. kyoto-uac jp environment T Hinoki·A. Kohyama The processing, structure and composition on Institute of Advanced Energy, Kyoto University, Gokasho, as-received Sic fibers have been presented in literature Uji, Kyoto 611-0011, Japan 8. These authors confirmed the chemical composition 2 Springer
Microstructural characterization and fracture properties of SiC-based fibers annealed at elevated temperatures J. J. Sha Æ T. Hinoki Æ A. Kohyama Received: 6 April 2006 / Accepted: 15 June 2006 / Published online: 22 February 2007 Springer Science+Business Media, LLC 2007 Abstract Ceramic matrix composites (CMCs) have been proposed as potential structural materials for application of high temperature technologies. Excellent high temperature performance of CMCs requires that fibers must have high enough thermal stability and sufficient mechanical properties throughout the service life. In order to clarify the correlation between the mechanical properties and the microstructure of SiCbased fibers, SiC-based fibers were annealed at elevated temperatures in Ar for 1 h. After annealing, the fracture strengths on these fibers were evaluated at room temperature by tensile test; the microstructural features were characterized by X-ray diffraction (XRD) and field emission scanning electron microscopy (FE-SEM). Furthermore, the fracture mechanics was applied to estimate the fracture toughness and the critical fracture energy of these fibers. As a result, excellent microstructure and mechanical stabilities were observed for SiC fibers with near-stoichiometric composition and high-crystallite structure. Combining the microstructure examination with tensile test indicates that the thermal and mechanical stabilities of SiC fibers at high temperatures were mainly controlled by their crystallization and composition as well as other factors. Introduction Currently, ceramic matrix composites (CMCs) have been proposed as potential structural materials for application of high temperature technologies, such as advanced energy-generation systems and propulsion systems [1–3]. The key to successful application of CMCs is judicious selection and incorporation of ceramic fiber reinforcement with proper chemical, physical and mechanical properties. For high temperature operation, the most critical fiber properties are high strength and its reliable retention throughout the service life. Low fiber strength and thermal stability could result in low fracture toughness and accelerate sub-critical crack propagation in CMCs. Recently developed SiC-based fibers with nearstoichiometric composition and high-crystallite structure, such as Hi-NicalonTM type S [4] and TyrannoTM-SA [5], are promising reinforcement for CMCs fabrication. These fibers experienced a pyrolysis or sintering process during fabrication and their microstructure and mechanical properties depend on the thermal history. On the other hand, CMCs may be applied or fabricated above the fiber’s processing temperature [1–3, 6, 7]. In many cases, SiC fibers were expected to expose to an environment with very high temperature and low oxygen partial pressure in which case, the performance of fibers could be changed by thermal exposure, since the thermal and mechanical stability of SiC fibers, which can vary with processing conditions, are very sensitive to high temperature environment. The processing, structure and composition on as-received SiC fibers have been presented in literature [8]. These authors confirmed the chemical composition J. J. Sha (&) International Innovation Center, Kyoto University, Sakyo-ku, Kyoto 606-8501, Japan e-mail: shajianjun@iic.kyoto-u.ac.jp T. Hinoki A. Kohyama Institute of Advanced Energy, Kyoto University, Gokasho, Uji, Kyoto 611-0011, Japan 123 J Mater Sci (2007) 42:5046–5056 DOI 10.1007/s10853-006-0579-5
J Mater Sci(2007)42:5046-5056 5047 of SiC fibers with several techniques, and revealed 14 um), Hi-Nicalon Type-S(HNLS: C/Si= 1.05, some other original features: The carbon-rich layer on oxygen=0.2 wt %, diameter: 12 um) and Tyranno the surface of the HNLS fiber(80 nm) is much thicker SA(TySA(Grade 3): C/Si= 1.05, oxygen 0.5 wt%, than that of HNL fiber (20 um); Tyranno-SA fiber alumina l wt%, diameter: 7 um). It is clear that HNL (about 10 um in diameter) has a carbon-rich core fiber contained excess carbon and low oxygen content indicating that near-stoichiometric composition is only The latter two have near-stoichiometric composition effective near edge region. Similar phenomenon on and high crystallinity. These fibers were put in a Tyranno-SA fiber was also observed by Colomban graphite crucible and then annealed in Ar under a et al. using the Raman Spectroscopy [9, 10]. Bunsell pressure of 10 Pa and held for 1 h at desired tempe et al. 11 also reported that both Hi-Nicalon Type s ature from 1, 300 to 1, 900C. The annealing condition and Tyranno-SA fiber contain excess carbon at triple has been described in more detail elsewhere [12] points of grain boundaries. The microstructure of Sic materials in high tempe rature an nd oxidative environ- Characterization ment is very sensitive to composition. Consequently, it is necessary to characterize the microstructure of Sic After annealing, several techniques were used to fibers at elevated temperatures in order to know the characterize the fiber microstructure features and degradation mechanism and to predict high tempera- fracture properties. The XRD with CuKx irradiation ture performance of CMCs. was applied to examine the present phase, and the In our former work [12], the tensile properties of the apparent crystallite size of B-Sic was estimated by annealed Sic fibers were investigated by tensile test, employing the Scherrer formula[13] and fundamental analysi on the microstructure of these fibers was performed by means of field-emission L=K. i/(D.cos 0) scanning electron microscopy(FE-SEM) and X-ray diffraction(XRD), but no attempts were made to where K is a constant(taken as 0.9),i the Cuko correlate the microstructure and the fractur length (i.e, 1=0.154056 D the half-value ties.As observed in this work [12], the fracture of the width of p-Sic (111) peak and e the Bragg angle Hi-NicalonM and the Hi-Nicalon M Type S fibers (0=17.50 for B-Sic (111)) mainly originated from critical flaw and showed a clear FE-SEM image analyses were carried out within a fracture mirror zone. Therefore, for practical applica- fiber tow and along the fiber length to check the tion of CMCs, it is requested to accumulate experi- diameter variation. Result showed that these fibers had mental data and to reveal the degradation mechanism a wide diameter variation within a tow. The diameter of Sic fibers with a consideration of the thermal- variations within a tow are 10.78-16.60 um for the chemical stability HNL fiber. 10.85-14 04 um for the hnls fiber. 520- In order to identify the factors, which affect the high 9.67 um for the TySA fiber, respectively. Based on this temperature performance of SiC fibers, this work result, the individual fiber diameter was measured for proceeded a complementary investigation on the precise strength calculation. FE-SEM was also used to microstructure features and fracture properties of Sic characterize the fibers surface morphologies and fibers annealed at elevated temperatures, and fracture surface. attempted to clarify the correlation between the Furthermore, the critical flaw size and fracture mechanical properties and the microstructure. The mirror size on the fracture surfaces of fiber fragments fracture toughness and the critical fracture energy at were measured by means of FE-SEM examination elevated temperatures were estimated using the frac- The fracture fragments were obtained by single fila- ture mechanics by measurement of the critical flaw ment tensile tests, which were performed at room Irror sIZ temperature in ambient atmosphere using a mechani cal testing apparatus (Instron Corp. Model 5581 according to ASTM-recommended procedures [14] The load was applied at a constant strain rate of Experimental procedure 2 x 10/s and measured by a load-cell of 2.5N. The individual filaments had a gauge length of 25.4 mm and Materials and annealing condition were aligned and glued on cardboard fixture with epoxy. For each fiber type, the total number of tests is The fibers examined in this study were Hi-NicalonM 220 The detailed testing procedure has been presented (HNL: C/Si= 1.39, oxygen=0.5 wt%, diameter: in the literatures [12, 15
of SiC fibers with several techniques, and revealed some other original features: The carbon-rich layer on the surface of the HNLS fiber (80 nm) is much thicker than that of HNL fiber (20 um); Tyranno-SA fiber (about 10 um in diameter) has a carbon-rich core indicating that near-stoichiometric composition is only effective near edge region. Similar phenomenon on Tyranno-SA fiber was also observed by Colomban et al. using the Raman Spectroscopy [9, 10]. Bunsell et al. [11] also reported that both Hi-Nicalon Type S and Tyranno-SA fiber contain excess carbon at triple points of grain boundaries. The microstructure of SiC materials in high temperature and oxidative environment is very sensitive to composition. Consequently, it is necessary to characterize the microstructure of SiC fibers at elevated temperatures in order to know the degradation mechanism and to predict high temperature performance of CMCs. In our former work [12], the tensile properties of the annealed SiC fibers were investigated by tensile test, and fundamental analysis on the microstructure of these fibers was performed by means of field-emission scanning electron microscopy (FE-SEM) and X-ray diffraction (XRD), but no attempts were made to correlate the microstructure and the fracture properties. As observed in this work [12], the fracture of the Hi-NicalonTM and the Hi-NicalonTM Type S fibers mainly originated from critical flaw and showed a clear fracture mirror zone. Therefore, for practical application of CMCs, it is requested to accumulate experimental data and to reveal the degradation mechanism of SiC fibers with a consideration of the thermalchemical stability. In order to identify the factors, which affect the high temperature performance of SiC fibers, this work proceeded a complementary investigation on the microstructure features and fracture properties of SiC fibers annealed at elevated temperatures, and attempted to clarify the correlation between the mechanical properties and the microstructure. The fracture toughness and the critical fracture energy at elevated temperatures were estimated using the fracture mechanics by measurement of the critical flaw size/mirror size. Experimental procedure Materials and annealing condition The fibers examined in this study were Hi-NicalonTM (HNL: C/Si = 1.39, oxygen = 0.5 wt%, diameter: 14 um), Hi-NicalonTM Type-S (HNLS: C/Si = 1.05, oxygen = 0.2 wt%, diameter: 12 um) and TyrannoTM SA (TySA (Grade 3): C/Si = 1.05, oxygen < 0.5 wt%, alumina < 1 wt%, diameter: 7 um). It is clear that HNL fiber contained excess carbon and low oxygen content. The latter two have near-stoichiometric composition and high crystallinity. These fibers were put in a graphite crucible and then annealed in Ar under a pressure of 105 Pa and held for 1 h at desired temperature from 1,300 to 1,900 C. The annealing condition has been described in more detail elsewhere [12]. Characterization After annealing, several techniques were used to characterize the fiber microstructure features and fracture properties. The XRD with CuKa irradiation was applied to examine the present phase, and the apparent crystallite size of b-SiC was estimated by employing the Scherrer formula [13]: L = K k=ðD cos hÞ ð1Þ where K is a constant (taken as 0.9), k the CuKa wavelength (i.e., k = 0.154056 nm), D the half-value width of b-SiC (111) peak and h the Bragg angle (h = 17.5 for b-SiC (111)). FE-SEM image analyses were carried out within a fiber tow and along the fiber length to check the diameter variation. Result showed that these fibers had a wide diameter variation within a tow. The diameter variations within a tow are 10.78–16.60 um for the HNL fiber, 10.85–14.04 um for the HNLS fiber, 5.20– 9.67 um for the TySA fiber, respectively. Based on this result, the individual fiber diameter was measured for precise strength calculation. FE-SEM was also used to characterize the fiber’s surface morphologies and fracture surface. Furthermore, the critical flaw size and fracture mirror size on the fracture surfaces of fiber fragments were measured by means of FE-SEM examination. The fracture fragments were obtained by single filament tensile tests, which were performed at room temperature in ambient atmosphere using a mechanical testing apparatus (Instron Corp. Model 5581) according to ASTM-recommended procedures [14]. The load was applied at a constant strain rate of 2 · 10–4/s and measured by a load-cell of 2.5 N. The individual filaments had a gauge length of 25.4 mm and were aligned and glued on cardboard fixture with epoxy. For each fiber type, the total number of tests is ‡20. The detailed testing procedure has been presented in the literatures [12, 15]. J Mater Sci (2007) 42:5046–5056 5047 123
5048 J Mater Sci(2007)42:5046-5056 Results and discussion The very sharp diffraction peaks of p-SiC in as- received HNLS and TySA fibers indicated that these XRD characterization ave een high-crystallite structure Figure la-c showed X-ray diffraction patterns of three (Fig 1b, c), because of their very high fabrication temperature(about 1,600C and 1, 800C for HNLS types of fibers annealed at elevated temperatures in Ar and TySA, respectively). The annealing at tempera- for 1 h. The XRD patterns of the as-received SiC fibers tures beyond 1, 600.C caused gradual crystallization of (111)(20=357°;d=0.251nm),(220)(20=60 B-SiC in HNLS fiber(Fig 1b) USing the Scherrer's formula, the apparent crystal d=0.154 nm)and(311)(20=7200. d=0.131 nm). lite size of B-SiC, Dsic, was calculated from the half- The phases present in the hNL fibers were B-SiC and value width of the (111) peak. The plot of the p-Sic XRD-amorphous carbon. After annealing at temper- crystallite size as a function of annealing temperature ature over 1,400C, two other peaks are also observed was shown in Fig. 2. Following Teatures we len and peak height increased with increasing the anneal- (i The grain coarsening of HNL fiber started at ing temperature which are indexed as the(200) and 1,400C. ( i)the crystallite size of B-Sic in HNLS and (222)crystal planes and more obvious in HNLS fibers TySA fiber remained almost constant as annealing annealed at temperatures over 1, 600C(ig 1b) temperature 1,600C, while higher temperature The diffraction peaks in HNL fiber become sharp annealing caused an continuous coarsening in crystal and narrow when temperature is higher than 1, 300C lite size of SiC in HNLS. The crystallite size of B-SiC in (Fig. la), while they are not so obvious for near-sto- TySA fibers appears to be little dependent on the ichiometeric fibers(Fig. 1b, c). Such changes in the annealing temperature. The crystallite sizes for as diffraction peaks of hNL fibers are due to the coales- ceived HNL, HNLS and TySA fibers are 4.0, 11. 4, cence of p-SiC nano-crystals caused by the decompo- and 22.7 nm, while they are 15.5, 30.3, and 25.5 nm for sition of the intergranular amorphous phase and fibers annealed at 1, 900 oC for 1 h, respectively thermally activated diffusion. The decomposition the intergranular amorphous SiC,Oy phase occurred at coalescence of B-Sic nanocrystals due to either about 1,300C in HNL fiber resulted in progressive decomposition of amorphous phase or diffusion of crystallization of B-SiC according to the reaction [16]: and C atoms at grain boundaries during exposure at high temperatures. For the bulk materials with clean SiCrOy-SiC(s)+ Sio(g)+Co(g) (2) grain boundaries, the grain growth proceeds through Fig. 1 X-ray diffractic patterns for SiC fibe (c)"1 annealed at elevated tem itures:(a)HNL fib (220(1 b)HNLS fiber;(c) TySA 1020304050 304050607080 28/degree 28/degree 2 Springer
Results and discussion XRD characterization Figure 1a–c showed X-ray diffraction patterns of three types of fibers annealed at elevated temperatures in Ar for 1 h. The XRD patterns of the as-received SiC fibers show three main peaks which were assigned to the (111) (2h = 35.7; d = 0.251 nm), (220) (2h = 60.0; d = 0.154 nm) and (311) (2h = 72.0; d = 0.131 nm). The phases present in the HNL fibers were b-SiC and XRD-amorphous carbon. After annealing at temperature over 1,400 C, two other peaks are also observed and peak height increased with increasing the annealing temperature, which are indexed as the (200) and (222) crystal planes and more obvious in HNLS fibers annealed at temperatures over 1,600 C (Fig. 1b). The diffraction peaks in HNL fiber become sharp and narrow when temperature is higher than 1,300 C (Fig. 1a), while they are not so obvious for near-stoichiometeric fibers (Fig. 1b, c). Such changes in the diffraction peaks of HNL fibers are due to the coalescence of b-SiC nano-crystals caused by the decomposition of the intergranular amorphous phase and thermally activated diffusion. The decomposition of the intergranular amorphous SiCxOy phase occurred at about 1,300 C in HNL fiber resulted in progressive crystallization of b-SiC according to the reaction [16]: SiCxOy ! SiC(s) + SiO(g) + CO(g) ð2Þ The very sharp diffraction peaks of b-SiC in asreceived HNLS and TySA fibers indicated that these fibers have already been high-crystallite structure (Fig. 1b, c), because of their very high fabrication temperature (about 1,600 C and 1,800 C for HNLS and TySA, respectively). The annealing at temperatures beyond 1,600 C caused gradual crystallization of b-SiC in HNLS fiber (Fig. 1b). Using the Scherrer’s formula, the apparent crystallite size of b-SiC, DSiC, was calculated from the halfvalue width of the (111) peak. The plot of the b-SiC crystallite size as a function of annealing temperature was shown in Fig. 2. Following features were observed: (i) The grain coarsening of HNL fiber started at 1,400 C. (ii) the crystallite size of b-SiC in HNLS and TySA fiber remained almost constant as annealing temperature < 1,600 C, while higher temperature annealing caused an continuous coarsening in crystallite size of SiC in HNLS. The crystallite size of b-SiC in TySA fibers appears to be little dependent on the annealing temperature. The crystallite sizes for asreceived HNL, HNLS and TySA fibers are 4.0, 11.4, and 22.7 nm, while they are 15.5, 30.3, and 25.5 nm for fibers annealed at 1,900 C for 1 h, respectively. The grain coarsening could be attributed to the coalescence of b-SiC nanocrystals due to either decomposition of amorphous phase or diffusion of Si and C atoms at grain boundaries during exposure at high temperatures. For the bulk materials with clean grain boundaries, the grain growth proceeds through 10 20 30 40 50 60 70 80 2θ/degree 2θ/degree 2θ/degree (111) (200) (220) (311) 1900°C (222) 1780°C 1400°C As recived 1600°C 10 20 30 40 50 60 70 80 (111) (200) (220) (311) (222) 1900°C 1780°C 1400°C As recived 1600°C (a) (b) (c) 10 20 30 40 50 60 70 80 (1 (200) (220) (311) 1900 (222) °C 1600°C 1400°C As recived 1780°C (111) 1600°C 1400°C 1780°C Fig. 1 X-ray diffraction patterns for SiC fibers annealed at elevated temperatures: (a) HNL fiber; (b) HNLS fiber; (c) TySA fiber : b-SiC 5048 J Mater Sci (2007) 42:5046–5056 123
J Mater Sci(2007)42:5046-5056 5049 large grains incorporating the small one by grain size, which was expected to have a high diffusivity at boundary diffusion. Especially, for grains with small grain boundaries and result in a large grain size as size, the grain boundary diffusion operates much more annealing at high temperatures. However, an unex readily. As observed in two Nippon Carbon fibers, the pected phenomenon was observed between two Nip grain coarsening is more obvious in annealed state than pon Carbon fibers. This can be attributed to the excess those of as-received state (tEM observations have carbon in HNL fiber. TEM observation revealed that revealed that grain size is about 5 nm for HNL fiber heat treatment of the hNL fiber results in a gradual [17], 20 nm for HNLS fiber [18], 200 nm for TySA fiber organization of the free carbon phase in terms of the [11). On the other hand, the residual trace oxygen may size of the carbon layer and the number of stacked lay a role in the Si and c grain boundary transport by layers as increasing temperatures [17. Takeda et al. accelerating diffusion [17], because the oxygen is not [20] have investigated the properties of polycarbosilen necessarily eliminated from the fiber as reported in the derived silicon carbide fibers with various C/Si com literature [8, even for the HNLS fiber which was positions, and revealed that microstructure and fabricated at very high temperature mechanical properties are quite dependent on the C/si onsidering the starting temperature for grain composition. Grain growth is suppressed with increase coarsening in Fig. 2, the grain size might be related in excess carbon. In other studies [21, 22), the carbon primarily to the maximum temperature at which the suppressing growth and coalescence of the Sic micro- fibers were fabricated. The fabrication temperatures crystals was also observed. Sasaki [22] found that car- have been presented for two Nippon Carbon fibers bon disappeared above 1,500C heat treatment in Sic (HNL: 1,350C, HNLS: 1, 600C) and for TySA fiber fiber using Raman study And then an abrupt increase (about 1, 800C)in the literature[19]. From the Fig. 2, of crystal size at 1, 500C was observed it can be seen that the crystallite size increased when For the TySA fiber, this fiber originally has a annealing temperature is above the fabrication tem- large crystallite size. In previous studies[8-10,a perature as expected. For hNL fiber, the grain coars- bon-rich core was revealed in TySA fiber, which results ening occurred at relatively low temperature is due to from the production process. Colomban et al. esti the decomposition of amorphous phase at about mated carbon grain size and Sic grain size in TySA 1,300C. On the other hand, the thermally activated fiber from Raman spectroscopy 9, 10]. The Carbon diffusion plays an important role on the grain coars- grains appear approximately 2-3 times smaller on the ening of Sic materials at high temperatures. fiber's core(0.9-1.7 nm)than on periphery (1 If we make a further comparison in crystallite size 2.6 nm). The grain size of Sic in fiber core is much between two Nippon Carbon fibers again, we can see smaller than edge region. Likely, this is due to that that a large difference in crystallite size was observed carbon suppressed the grain growth of B-SiC.Fur for two fibers annealed at same temperature. As above thermore, this fiber contains the small amount of alu mentioned, the HNL fiber has an small starting grain mina(less than 1 wt %)as sintering additive, which will also inhibit the grain growth of Sic. As a result, the TySA fiber showed an excellent thermal stability in Ar HNL atmosphere ATySA Tensile strength Tensile strengths were obtained by a single filament tensile test technique at room temperature. If plotting the tensile data into the Fig. 2. it is obvious that the strengths of annealed fiber were related to B-SiC crystallite size(Dsic) as shown in Fig 3. The Fig 3 confirmed the fact that generally materials with large grain size have low strengths. The growth of Sic crystals reduces the bonding forces at the grain Initial12001400160018002000 boundaries. Since the manufactures are always seeking Annealing temperature, T/c the optimal fabrication temperature at which the uperior thermal stability and excellent mechanical Fig 2 Apparent crystallite size of B-SiC for Sic fibers annealed strength can be obtained simultaneously, thus, the at elevated temperatures in Ar for 1 h upper fabrication temperatures are typically fixed by
large grains incorporating the small one by grain boundary diffusion. Especially, for grains with small size, the grain boundary diffusion operates much more readily. As observed in two Nippon Carbon fibers, the grain coarsening is more obvious in annealed state than those of as-received state (TEM observations have revealed that grain size is about 5 nm for HNL fiber [17], 20 nm for HNLS fiber [18], 200 nm for TySA fiber [11]). On the other hand, the residual trace oxygen may play a role in the Si and C grain boundary transport by accelerating diffusion [17], because the oxygen is not necessarily eliminated from the fiber as reported in the literature [8], even for the HNLS fiber which was fabricated at very high temperature. Considering the starting temperature for grain coarsening in Fig. 2, the grain size might be related primarily to the maximum temperature at which the fibers were fabricated. The fabrication temperatures have been presented for two Nippon Carbon fibers (HNL: 1,350 C, HNLS: 1,600 C) and for TySA fiber (about 1,800 C) in the literature [19]. From the Fig. 2, it can be seen that the crystallite size increased when annealing temperature is above the fabrication temperature as expected. For HNL fiber, the grain coarsening occurred at relatively low temperature is due to the decomposition of amorphous phase at about 1,300 C. On the other hand, the thermally activated diffusion plays an important role on the grain coarsening of SiC materials at high temperatures. If we make a further comparison in crystallite size between two Nippon Carbon fibers again, we can see that a large difference in crystallite size was observed for two fibers annealed at same temperature. As above mentioned, the HNL fiber has an small starting grain size, which was expected to have a high diffusivity at grain boundaries and result in a large grain size as annealing at high temperatures. However, an unexpected phenomenon was observed between two Nippon Carbon fibers. This can be attributed to the excess carbon in HNL fiber. TEM observation revealed that heat treatment of the HNL fiber results in a gradual organization of the free carbon phase in terms of the size of the carbon layer and the number of stacked layers as increasing temperatures [17]. Takeda et al. [20] have investigated the properties of polycarbosilenderived silicon carbide fibers with various C/Si compositions, and revealed that microstructure and mechanical properties are quite dependent on the C/Si composition. Grain growth is suppressed with increase in excess carbon. In other studies [21, 22], the carbon suppressing growth and coalescence of the SiC microcrystals was also observed. Sasaki [22] found that carbon disappeared above 1,500 C heat treatment in SiC fiber using Raman study. And then an abrupt increase of crystal size at 1,500 C was observed. For the TySA fiber, this fiber originally has a very large crystallite size. In previous studies [8–10], a carbon-rich core was revealed in TySA fiber, which results from the production process. Colomban et al. estimated carbon grain size and SiC grain size in TySA fiber from Raman spectroscopy [9, 10]. The Carbon grains appear approximately 2–3 times smaller on the fiber’s core (0.9–1.7 nm) than on its periphery (1.7– 2.6 nm). The grain size of SiC in fiber core is much smaller than edge region. Likely, this is due to that carbon suppressed the grain growth of b-SiC. Furthermore, this fiber contains the small amount of alumina (less than 1 wt%) as sintering additive, which will also inhibit the grain growth of SiC. As a result, the TySA fiber showed an excellent thermal stability in Ar atmosphere. Tensile strength Tensile strengths were obtained by a single filament tensile test technique at room temperature. If plotting the tensile data into the Fig. 2, it is obvious that the strengths of annealed fiber were related to b-SiC crystallite size (DSiC) as shown in Fig. 3. The Fig. 3 confirmed the fact that generally materials with large grain size have low strengths. The growth of SiC crystals reduces the bonding forces at the grain boundaries. Since the manufactures are always seeking the optimal fabrication temperature at which the superior thermal stability and excellent mechanical strength can be obtained simultaneously, thus, the upper fabrication temperatures are typically fixed by 0 5 10 15 20 25 30 35 1200 1400 1600 1800 2000 HNL HNLS TySA Initial Annealing temperature, T/C Fig. 2 Apparent crystallite size of b-SiC for SiC fibers annealed at elevated temperatures in Ar for 1 h J Mater Sci (2007) 42:5046–5056 5049 123
5050 J Mater Sci(2007)42:5046-5056 150.0 23 produced a laboratory fiber (UF fiber)with the ◆·HNL similar composition as HNL fiber. There was no loss strength with heat treatments up to 1, 700C and then the strength decreased rapidly with further heat treat 0 ments up to 1,900C. He believed that strength is controlled by the residual tensile stresses, which expansion coefficient between SiC and C. This situa tion should be true. The coefficient of thermal expan sion of carbon/graphite(2.0-3.0 x 10/K)is less than SiC(3.9-4.0 x 10-/K). When fibers were cooled from high annealing temperature to room temperature, the nitial12001400160018002000 Sic grains want to contract, while carbon grain w Annealing temperature, C resist their contraction. This action-reaction will put Fig. 3 Tensile strength and its relation to the crystallite size for SiC in tension and carbon in compression. This residual SiC fibers annealed at elevated temperatures in Ar for 1 h tension stresses could have a contribution to the total stress loss. This case can be applied to each fiber type those temperature conditions above which perfor- which contains excess carbon, but here it should be mance degradation of the fibers occurred. The depen- more significant in HNL fiber because of high excess dence of strength on temperature in present study is in carbon(C/Si= 1.38). In both HNL fiber and TySA agreement with those of previous studies [5, 17, 18, 22]. fiber, the size of carbon grain increased with increasing Ichikawa et al. [18] reported that HNLS was quite annealing temperature [9, 10, 17]. The growth of the stable chemically after 1 h exposure in an argon gas at carbon corresponds to a decrease of localized spin 1, 800C, since no structural decomposition occurred centres [24. The growth of the carbon grain might and it exhibited a good strength of 1.9 GPa. The result in an increase of residual stress however, this crystallite size is about 35 nm. TEM observation shows evidence is insufficient because the magnitude of that this annealed HNLS fiber has a Sic grain size of residual stresses is strongly dependent on the volume approximately 200 nm, which is about 10 times larger fraction of carbon phase in a bulk material than that of the as-received fiber As for TysA fiber, this is a sintering fiber, which is Surface morphologies prepared by the reaction of a polyc h aluminiumacetylacetonate, and subsequently con- Figure 4 showed SEM morphologies of the fibers after verted into the Tyranno SA fiber, by decomposition with annealing at elevated temperatures in Ar for 1 h an evolution of CO and Sio (1,500C<T< 1, 700C) The HNL fibers annealed at temperatures below and sintering(about 1, 800C). TySA fiber retained 1, 400C had a smooth surface which is almost no most of its initial strength, because no significant grain difference from that of as received fibers( Fig. 4a) coarsening was observed even annealed at 1,900C. Annealing at 1,400 C caused slight coarsening of fiber Excellent strength retention has been observed in a surface( Fig 4b). Obvious changes in appearance were former work 5 observed for the fibers annealed at 1.780oC. These On the other hand, the HNL fiber has smaller crystal fibers showed a porous microstructure and large grain size comparing to that of HNLS fiber, but it showed deposition on the fiber surface(Fig. 4c). Such huge more rapid strength degradation than HNLS fiber crystals are not observed within bulk of the fiber, due above 1,400C annealing as shown in Fig 3; both to the presence of free carbon, which inhibit the grain HNLS and TysA fiber have near-stoichiometric com- boundary or/and gaseous diffusion position and high-crystallite structure, but they showed For the hnls fibers annealed below 1. 600 oC. their different strength retention. This observed phenome- microstructure did not vary compared to the as- non implied that other mechanisms must be responsi- received fibers(Fig. 4d). After annealing at 1, 600C, ble for strength degradation of Sic fibers besides the although the individual SiC grain grown on the fiber coarsening of crystallite size urface. but fiber surface still remained smooth and it One source for strength degradation is residual appeared no structure degradation(Fig. 4e). The fiber stresses, which were generated from phase transfor- annealed at 1, 780 C exhibited a rough surface with mation and the mismatch in the coefficient of thermal deposition of bulk SiC grains, but it still remained expansion between excess car bon and SiC grain Sacks relatively dense structure(Fig. 4f) 2 Springer
those temperature conditions above which performance degradation of the fibers occurred. The dependence of strength on temperature in present study is in agreement with those of previous studies [5, 17, 18, 22]. Ichikawa et al. [18] reported that HNLS was quite stable chemically after 1 h exposure in an argon gas at 1,800 C, since no structural decomposition occurred and it exhibited a good strength of 1.9 GPa. The crystallite size is about 35 nm. TEM observation shows that this annealed HNLS fiber has a SiC grain size of approximately 200 nm, which is about 10 times larger than that of the as-received fiber. As for TySA fiber, this is a sintering fiber, which is prepared by the reaction of a polycarbosilane (PCS) with aluminiumacetylacetonate, and subsequently converted into the Tyranno SA fiber, by decomposition with an evolution of CO and SiO (1,500 C <T < 1,700 C) and sintering (about 1,800 C). TySA fiber retained most of its initial strength, because no significant grain coarsening was observed even annealed at 1,900 C. Excellent strength retention has been observed in a former work [5]. On the other hand, the HNL fiber has smaller crystal size comparing to that of HNLS fiber, but it showed more rapid strength degradation than HNLS fiber above 1,400 C annealing as shown in Fig. 3; both HNLS and TySA fiber have near-stoichiometric composition and high-crystallite structure, but they showed different strength retention. This observed phenomenon implied that other mechanisms must be responsible for strength degradation of SiC fibers besides the coarsening of crystallite size. One source for strength degradation is residual stresses, which were generated from phase transformation and the mismatch in the coefficient of thermal expansion between excess carbon and SiC grain. Sacks [23] produced a laboratory fiber (UF fiber) with the similar composition as HNL fiber. There was no loss in strength with heat treatments up to 1,700 C and then the strength decreased rapidly with further heat treatments up to 1,900 C. He believed that strength is controlled by the residual tensile stresses, which developed as a result of the mismatch in thermal expansion coefficient between SiC and C. This situation should be true. The coefficient of thermal expansion of carbon/graphite (2.0–3.0 · 10–6/K) is less than SiC (3.9–4.0 · 10–6/K). When fibers were cooled from high annealing temperature to room temperature, the SiC grains want to contract, while carbon grain will resist their contraction. This action-reaction will put SiC in tension and carbon in compression. This residual tension stresses could have a contribution to the total stress loss. This case can be applied to each fiber type, which contains excess carbon, but here it should be more significant in HNL fiber because of high excess carbon (C/Si = 1.38). In both HNL fiber and TySA fiber, the size of carbon grain increased with increasing annealing temperature [9, 10, 17]. The growth of the carbon corresponds to a decrease of localized spin centres [24]. The growth of the carbon grain might result in an increase of residual stress however, this evidence is insufficient because the magnitude of residual stresses is strongly dependent on the volume fraction of carbon phase in a bulk material. Surface morphologies Figure 4 showed SEM morphologies of the fibers after annealing at elevated temperatures in Ar for 1 h. The HNL fibers annealed at temperatures below 1,400 C had a smooth surface, which is almost no difference from that of as received fibers (Fig. 4a). Annealing at 1,400 C caused slight coarsening of fiber surface (Fig. 4b). Obvious changes in appearance were observed for the fibers annealed at 1,780 C. These fibers showed a porous microstructure and large grains deposition on the fiber surface (Fig. 4c). Such huge crystals are not observed within bulk of the fiber, due to the presence of free carbon, which inhibit the grain boundary or/and gaseous diffusion. For the HNLS fibers annealed below 1,600 C, their microstructure did not vary compared to the asreceived fibers (Fig. 4d). After annealing at 1,600 C, although the individual SiC grain grown on the fiber surface, but fiber surface still remained smooth and it appeared no structure degradation (Fig. 4e). The fiber annealed at 1,780 C exhibited a rough surface with deposition of bulk SiC grains, but it still remained a relatively dense structure (Fig. 4f). 0.0 1.0 2.0 3.0 4.0 1200 1400 1600 1800 2000 0.0 10.0 20.0 30.0 40.0 50.0 Crystallite size,nm Initial HNL HNLS TySA Annealing temperature, οC Tensile strength, /GPa Fig. 3 Tensile strength and its relation to the crystallite size for SiC fibers annealed at elevated temperatures in Ar for 1 h 5050 J Mater Sci (2007) 42:5046–5056 123